Desa H) AND VM42(B, H) AND VM42P(B, VM36P installation manual Wall Switch Installation

Page 10

10

INSTALLATION

WALL SWITCH INSTALLATION

The installation of a wall switch allows you to activate the gas control valve without the normal household electricity since the valve operates on millivolt current supplied by the heat generated by the thermopile. To install the wall switch:

1.

Remove the front refractory access panel by lifting up and

 

angling out of the firebox opening (see Figure 13).

2.

Use wire and connectors provided. Attach red wire to terminal

4.Connect wires to control circuit. Connect white wire to termi- nal marked TH/TP on control valve. Connect red wire to male blade connector provided at open end of safety circuit wiring (see Wiring Diagram, page 18).

5.Locate the battery clip mounted on the back of the receiver (see Figure 16).

6.Slide 9-volt battery (not included) through the clip. Note: Only use alkaline battery.

7.Attach the terminal wires to the battery (see Figure 16).

8.Replace refractory brick access panel.

marked TH/TP on control valve. Attach white wire to blade

connector on open end of safety circuit wiring (see Wiring

Diagram, page 18).

Note: If any of the original wire from the unit control must be re- placed, use the same type or a higher rated wire (25 ft. maximum length).

WARNING: Do not wire remote wall switch to main power supply (Standard 120v household current).

3.

Locate wall switch in a convenient location.

IN

 

ON

LO

T

 

I

 

P

 

FFO

IN

OUT

To Safety Circuit

Route Millivolt

Wall Switch

Wires (Supplied)

(Supplied)

 

 

Through Gas Line

 

 

Conduit Sleeve

 

 

To Thermopile

 

TH

 

 

TP

 

 

THTP

 

 

 

 

(Back View

4.

After wire connections are complete, replace refractory access

 

panel.

Note:Ifanyoftheoriginalwireassuppliedmustbereplaced,use18AWG TYPE CL2 (UL) 105 C (25 ft. length MAXIMUM) or equivalent.

Figure 13 - Removing Front Refractory Access Panel

OPTIONAL WIRELESS HAND-HELD REMOTE CONTROL INSTALLATION

Note: If using optional wireless hand-held remote control, the wall switch is no longer operational.

Installing Receiver

1.Remove the front refractory access panel by lifting up and angling out of the firebox opening (see Figure 13) to expose controls.

2.Disconnect wall switch wires from TH and TH/TP terminals on control valve (see Figure 14).

3.Install remote receiver unit onto mounting bracket using the two plastic mounting clips (see Figure 15).

Figure 14 - Wall Switch Wiring Diagram

 

 

9-Volt Battery

Receiver

Battery

 

 

 

 

Clip

 

Plastic

Terminal

 

Mounting

 

Wires

 

Clips

 

 

 

Mounting Bracket

 

Receiver

 

 

Figure 15 - Installing Remote

Figure 16

- Installing Battery

Receiver (Shown from Rear of

in Receiver

Mounting Bracket)

 

 

Installing 9-Volt Battery in Hand-Held Remote

Control Unit

 

 

1.Remove battery cover on back of remote control unit.

2.Attach terminal wires to the battery (not included). Place battery into the battery housing. Note: Only use alkaline battery.

3.Replace battery cover onto remote control unit.

Battery Cover

Remote Control Unit

 

Terminal Wires

 

9-Volt

 

Battery

 

 

Battery

 

Housing

Figure 17 - Installing Battery in Hand-Held Remote Control Unit

For more information, visit www.desatech.com

108795-01M

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Vent Decorative GAS Fireplace OWNER’S Operation and Installation ManualWhat to do if YOU Smell GAS Table of Contents Safety InformationIntroduction Safety InformationUnpacking Before YOU BeginProduct Specifications GAS Rating NaturalSelecting Location PRE-INSTALLATION PreparationClearances Mantel Clearances and Wall Details 229mm Materials Header 152mm BSpacer 76mm 38mm MaxInstalling Transition Pipe and Starter Collar PRE-INSTALLATION PreparationFraming Venting Installation Typical B-Vent ConfigurationVenting Installation Checking for Proper VentingWall Switch Installation InstallationOptional Wireless HAND-HELD Remote Control Installation Installation GAS Line HOOK-UPEmber and PAN Material Placement LOG Placement for M36, M36P, VM36 and VM36P ModelsLOG Placement for M42, M42P, VM42 and VM42P Models Lava rock provided around the front and sides of the burnerCombustion AIR KIT Model AK4 Optional Appliance EnclosureInstalling Optional Glass Door Accessory Opening Vent DamperLighting Instructions For Your Safety Read Before LightingOperating Fireplace To Turn OFF GAS To ApplianceOperating Fireplace Pilot AssemblyInspecting Burners Optional HAND-HELD Remote OperationReplacement Parts Cleaning Maintenance Service HintsTechnical Service Wiring DiagramTroubleshooting Observed Problem Possible Cause RemedyTroubleshooting MainGas leak. See Warning statement at Illustrated Parts Breakdown ModelsParts List Parts Available not ShownIllustrated Parts Breakdown Logsets for ModelsOwners Registration Form Postage Required Accessories Warranty Information

VM36P, H) AND VM42(B, M42P, H) AND VM42P(B, M36P specifications

Desa H), M36P, H) and VM42P(B, M42P, H) and VM42(B are notable entities in the realm of technological solutions, particularly in the fields of engineering and manufacturing. These designations often pertain to advanced machine models or systems that incorporate various characteristics tailored for specific industrial applications.

The Desa H) series is recognized for its robust performance in industrial settings. It typically features enhanced efficiency and durability, making it suitable for rigorous operational environments. The key technologies integrated into the Desa H) models include high-performance motors and precision control systems that ensure optimal functionality. In particular, these systems are designed to minimize energy consumption while maximizing output across diverse applications.

Meanwhile, the M36P and its variants, including the M36P,H), are engineered with versatility in mind. They are equipped with modular components that allow for easy customization based on user requirements. This adaptability is a significant advantage, as it enables operators to modify the system to suit various tasks without extensive reconfiguration. Noteworthy features of the M36P series include advanced user interfaces that facilitate ease of operation and monitoring.

The VM42P(B, M42P, H) series takes innovation a step further by integrating state-of-the-art automation technologies. With features like smart sensors and AI-driven analytics, the VM42 models provide unprecedented levels of precision and reliability. These technologies enable predictive maintenance, allowing users to anticipate potential issues before they arise, thus reducing downtime and operational costs. The VM42(B) variant is particularly appreciated for its high throughput capabilities, making it ideal for mass production settings.

All models share common characteristics such as rugged construction, user-friendly interfaces, and compliance with international safety standards. Additionally, they are designed for scalability, which ensures that businesses can expand their operations with ease as demand grows. Enhanced connectivity options and IoT integration further allow for real-time data analysis and remote monitoring, fostering smarter production environments.

In summary, the Desa H), M36P, H) and VM42P(B, M42P, H) and VM42(B series represent a fusion of innovative engineering and practical application. Each model’s distinct features cater to a broad range of industrial needs, making them indispensable tools in modern manufacturing and engineering landscapes. Through their commitment to efficiency, adaptability, and intelligent technology, these systems pave the way for enhanced productivity and sustainability in various sectors.
Top Page Image Contents