Vermont Casting WinterWarm Fireplace Insert or System Cabinet convection blower in place behind

Page 31

 

Optional

 

Blower

 

Elevated Base

Junction Box

FP1126

Fig. 47 Slide the elevated base platform into the cabinet until it contacts the back panel.

 

Flange attaches

Cabinet Convection

 

to cabinet rear

Blower Housing

 

wall

 

 

Flange

 

 

attaches to

 

 

base

 

Convectiion

 

Blower Power

 

Cord

 

 

 

Elevated Base

FP1127

 

 

Fig. 48

The cabinet convection blower in place behind the

base.

 

 

WinterWarm Fireplace Insert or System

Use drywall screws to fasten the wall covering to the metal standoff and drywall stops at the cabinet. Drill pilot holes through the wall covering material and one thickness of the sheet metal with a #40 (.098”) drill bit. Tape and fill holes and/or seams and decorate your chase wall at this time.

11.Install the vent grilles. Position the cast grilles over the duct box openings, and mark for the four screw holes in each. Using a 5/32” (4mm) bit, drill through the drywall and duct box flanges, and install the grilles with the slot head black oxide screws.

Once the vent grilles have been installed, you are ready to complete the installation by installing the fire cham- ber and the front.

2000941

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents WinterWarm Introduction Table of ContentsWinterWarm SpecificationsDamper Section I OperationYour WinterWarm’s Controls What They Do Primary Air ControlFans Use the Air Control Settings That Work Best for YouBurn Only High-Quality Wood Starting and Maintaining a Wood Fire How To Build a Wood Fire Keep It GoingWinterWarm Control Settings High-Efficiency Wood Burning With Catalytic CombustionReloading and Reviving a Wood Fire Open-Fire Viewing With the Screen Cassette Special Tactics for Cold-Climate HeatingRemove and Store Ash Safely Care of the Porcelain Enamel Surface Section II MaintenanceCleaning the Glass Care of the Cast Iron SurfaceHow to Replace Gaskets Adjust the Door Latch PeriodicallyReplaceable WinterWarm Fiberglass Gaskets Permanent WinterWarm Gaskets Replacing the Door GasketsReplacing the Damper Gasket Replace Damaged Door Glass ImmediatelyCare of the Catalytic Combustor Adjust the Damper as NeededTry the Fine Adjustment First Use the Coarse Adjustment Only If NecessaryInspection and Removal of the Combustor When to Suspect a Combustor ProblemWatch for Better Results Clean Chimney System is Safer and Works BetterLearn to Recognize and Avoid Creosote Two Weeks WinterWarm Maintenance ScheduleYearly Spring Cleaning Fireplace DailyPH4 Large WinterWarm Wiring DiagramRequirements of your Existing Masonry Chimney Minimum Fireplace DimensionsSection III Preparing a Masonry Chimney Requirements for Existing Masonry FireplaceHearth Requirements Clearance RequirementsFireplace Maximums Flex Connector System Chimney ConnectorSealing Requirements Remove the Masonry Fireplace Damper Install the Flex ConnectorCustom Damper Seal Relined ChimneyReverse the Flue Collar If Necessary Install the Floor ProtectorSelecting a Location for Your Fireplace Section IV Installing the Fireplace System CabinetStructural Considerations Installation Chase Dimensions Carefully Observe Local Building CodesChimney Requirements Duct and Vent Placementfloor protector must satisfy these requirements Guidelines for an Outside Air SupplyImportant Reminders Flush with the Floor or Laid Over It?Customizing the Finished Appearance Electrical RequirementsChoosing a Facing Material Use the Right Adhesives Prepare and Install WinterWarm Cabinet 40³⁄ ₈ 1026mm Install the optional cabinet convection blower kit Install the elevated base. Slide the base intoCabinet convection blower in place behind Prepare and Install WinterWarm Firechamber Section V Completing the WinterWarm InstallationConnect the Outside Air Duct to the Air Box Fireplace System onlyPrepare and Install the WinterWarm Front Attach the Rheostat Rod Linkages Connect the WiringInstall the Air Divider Install and Adjust the ControlsMove the Entire Unit the final few inches into the Cabinet Install the Latticework PanelsInstall the Mantel Fireplace Systems only Install the PlinthWinterWarm Large Insert WinterWarm Large Insert Classic Sand Midnight Shell Enamel Parts WinterWarm Large Insert ModelAppendixApproved Chimney Components Appendix Catalytic Combustor Warranty CFM Corporation

WinterWarm Fireplace Insert or System specifications

The Vermont Casting WinterWarm fireplace insert is a remarkable addition to any home, delivering both efficiency and elegance to your living space. Designed to enhance heat delivery and overall ambiance, this insert is a popular choice among homeowners looking to create a warm and inviting atmosphere during the colder months.

One of the standout features of the WinterWarm insert is its efficient heating capability. With a remarkable heating capacity that can warm up to 2,000 square feet, this system transforms your drafty fireplace into a powerful heat source. The efficient design maximizes heat output while minimizing the amount of wood needed, ensuring you stay warm without emptying your wallet on heating costs.

The insert also incorporates advanced technology that promotes cleaner burning and reduced emissions. With its secondary combustion system, the WinterWarm optimizes the burn process, allowing for improved heat production and cleaner air. This feature not only benefits the environment but also extends the life of the unit, making it a sustainable choice for homeowners.

Aesthetically, the Vermont Casting WinterWarm insert doesn’t compromise on style. It is available in various finishes, including classic black and elegant enamel options, allowing homeowners to choose a unit that seamlessly blends with their home decor. The large viewing window provides a lovely view of the flames, enhancing the cozy feel of your room while adding a touch of sophistication.

The construction of the WinterWarm insert is another highlight. Made from durable cast iron, this unit is built to last, ensuring that it will provide warmth and comfort for many winters to come. The cast iron not only offers exceptional heat retention but also contributes to the timeless charm of the insert.

Additionally, the WinterWarm insert features an easy-to-use air control system, allowing you to adjust the burn rate and heat output quickly. This user-friendly design makes it accessible for everyone, whether you are a seasoned wood-burning enthusiast or new to the experience.

In summary, the Vermont Casting WinterWarm fireplace insert is an outstanding option for those looking to combine efficiency with style. With its powerful heating capabilities, advanced combustion technology, and elegant design, it transforms any standard fireplace into the heart of your home during winter months. This fireplace insert not only enhances indoor comfort but also adds a timeless element to your living space, making it a worthwhile investment for homeowners.
Top Page Image Contents