Vermont Casting WinterWarm Fireplace Insert or System Special Tactics for Cold-Climate Heating

Page 8

WinterWarm Fireplace Insert or System

NOTE: If the charcoal bed is relatively thick and your fuel is well-seasoned, it is possible to add fresh fuel (smaller pieces first), close the door and damper, and reset the air control within five minutes.

Special Tactics for Cold-Climate Heating

The WinterWarm is capable of producing up to 50,000 Btu’s/hour and heating an area of up to 1,500 ft.2 (140 m2) However, many factors affect heating performance and can influence the extent to which the WinterWarm can heat a given area.

A well-insulated home, located in a moderate climate and with the WinterWarm Fireplace Insert or Fireplace System located centrally in an open floor plan, will be easier to heat than a drafty home in the far north in which a WinterWarm is installed on an exterior wall at the end of a long house.

In Fireplace Insert installations, over-sized chimneys can produce less effective results than those that are properly sized, and interior chimneys usually perform better than those located outside the house.

Different results may be experienced even in the same installation if you switch from burning good, dry wood to wood that is partially rotted or inadequately seasoned.

To compensate for these factors in cold climates, it may be necessary to operate the WinterWarm for longer periods of time than described above before closing the damper, or to leave the air control set to a higher level more of the time.

Open-Fire Viewing

with the Screen Cassette

The cassette screen that was included with your Win- terWarm is interchangeable with the glass cassette, en- abling you to convert from closed-door wood burning to protected open-fire viewing. Always leave the damper open when operating the WinterWarm with the screen in the open-fire mode.

To change cassettes, use this procedure:

Let the WinterWarm cool completely

•Open the door

•Loosen the two short retainer clips, one at each top corner of the cassette frame, and turn them to clear the frame.

•Tilt the top edge of the cassette away from the door frame.

•Carefully remove the cassette, being especially careful with the glass cassette. Store the unused cassette for future use.

8

•Examine the gasket that seals the cassette to the perimeter of the door frame. Contact your local dealer if you need a replacement gasket.

•Check the bottom channel of the door frame for debris, and clean if necessary.

•Insert the new cassette, bottom edge first, then the top edge.

IMPORTANT: The glass used in your WinterWarm is coated with a special material on one side that reflects heat back into the fire chamber. Before replacing a glass cassette that has been removed, examine the metal frame. One side has smooth, mitered corner joints; the other side has rough weld marks.

To install the glass correctly, the smooth mitered corners must be facing the gasket and the rough weld marks must be positioned toward the fire chamber.

•Replace the two retainer clips, applying just enough pressure to secure the cassette evenly against the gasket.

Remove and Store Ash Safely

Check the ash pan before reloading the stove, and empty if necessary using the following procedure:

•Open the damper

•Open the load door (Fig. 7)

•Pull open the ash chamber door with the hooked end of the fall-away handle.

•If the ash level is nearing the top, place the removable cover over the pan and make sure it is completely engaged. Ash may contain hot coals and must be treated with extreme care.

•Take the pan outdoors and empty the ash into your ash container.

 

FP1075

Fig. 7

Carefully remove ash pan.

 

2000941

Page 7 Page 9
Image 8
Page 7 Page 9
Contents WinterWarm Table of Contents IntroductionSpecifications WinterWarmSection I Operation Your WinterWarm’s Controls What They DoPrimary Air Control DamperBurn Only High-Quality Wood Use the Air Control Settings That Work Best for YouFans How To Build a Wood Fire Keep It Going WinterWarm Control SettingsHigh-Efficiency Wood Burning With Catalytic Combustion Starting and Maintaining a Wood FireReloading and Reviving a Wood Fire Remove and Store Ash Safely Special Tactics for Cold-Climate HeatingOpen-Fire Viewing With the Screen Cassette Section II Maintenance Cleaning the GlassCare of the Cast Iron Surface Care of the Porcelain Enamel SurfaceReplaceable WinterWarm Fiberglass Gaskets Adjust the Door Latch PeriodicallyHow to Replace Gaskets Replacing the Door Gaskets Replacing the Damper GasketReplace Damaged Door Glass Immediately Permanent WinterWarm GasketsAdjust the Damper as Needed Try the Fine Adjustment FirstUse the Coarse Adjustment Only If Necessary Care of the Catalytic CombustorWhen to Suspect a Combustor Problem Inspection and Removal of the CombustorLearn to Recognize and Avoid Creosote Clean Chimney System is Safer and Works BetterWatch for Better Results WinterWarm Maintenance Schedule Yearly Spring CleaningFireplace Daily Two WeeksLarge WinterWarm Wiring Diagram PH4Minimum Fireplace Dimensions Section III Preparing a Masonry ChimneyRequirements for Existing Masonry Fireplace Requirements of your Existing Masonry ChimneyFireplace Maximums Clearance RequirementsHearth Requirements Sealing Requirements Chimney ConnectorFlex Connector System Install the Flex Connector Custom Damper SealRelined Chimney Remove the Masonry Fireplace DamperInstall the Floor Protector Reverse the Flue Collar If NecessarySection IV Installing the Fireplace System Cabinet Structural Considerations Installation Chase DimensionsCarefully Observe Local Building Codes Selecting a Location for Your FireplaceDuct and Vent Placement Chimney RequirementsGuidelines for an Outside Air Supply floor protector must satisfy these requirementsFlush with the Floor or Laid Over It? Important RemindersChoosing a Facing Material Electrical RequirementsCustomizing the Finished Appearance Use the Right Adhesives Prepare and Install WinterWarm Cabinet 40³⁄ ₈ 1026mm Install the elevated base. Slide the base into Install the optional cabinet convection blower kitCabinet convection blower in place behind Section V Completing the WinterWarm Installation Prepare and Install WinterWarm FirechamberFireplace System only Connect the Outside Air Duct to the Air BoxPrepare and Install the WinterWarm Front Connect the Wiring Attach the Rheostat Rod LinkagesInstall and Adjust the Controls Install the Air DividerInstall the Latticework Panels Install the MantelFireplace Systems only Install the Plinth Move the Entire Unit the final few inches into the CabinetWinterWarm Large Insert WinterWarm Large Insert Shell Enamel Parts WinterWarm Large Insert Model Classic Sand MidnightAppendixApproved Chimney Components Appendix Catalytic Combustor Warranty CFM Corporation

WinterWarm Fireplace Insert or System specifications

The Vermont Casting WinterWarm fireplace insert is a remarkable addition to any home, delivering both efficiency and elegance to your living space. Designed to enhance heat delivery and overall ambiance, this insert is a popular choice among homeowners looking to create a warm and inviting atmosphere during the colder months.

One of the standout features of the WinterWarm insert is its efficient heating capability. With a remarkable heating capacity that can warm up to 2,000 square feet, this system transforms your drafty fireplace into a powerful heat source. The efficient design maximizes heat output while minimizing the amount of wood needed, ensuring you stay warm without emptying your wallet on heating costs.

The insert also incorporates advanced technology that promotes cleaner burning and reduced emissions. With its secondary combustion system, the WinterWarm optimizes the burn process, allowing for improved heat production and cleaner air. This feature not only benefits the environment but also extends the life of the unit, making it a sustainable choice for homeowners.

Aesthetically, the Vermont Casting WinterWarm insert doesn’t compromise on style. It is available in various finishes, including classic black and elegant enamel options, allowing homeowners to choose a unit that seamlessly blends with their home decor. The large viewing window provides a lovely view of the flames, enhancing the cozy feel of your room while adding a touch of sophistication.

The construction of the WinterWarm insert is another highlight. Made from durable cast iron, this unit is built to last, ensuring that it will provide warmth and comfort for many winters to come. The cast iron not only offers exceptional heat retention but also contributes to the timeless charm of the insert.

Additionally, the WinterWarm insert features an easy-to-use air control system, allowing you to adjust the burn rate and heat output quickly. This user-friendly design makes it accessible for everyone, whether you are a seasoned wood-burning enthusiast or new to the experience.

In summary, the Vermont Casting WinterWarm fireplace insert is an outstanding option for those looking to combine efficiency with style. With its powerful heating capabilities, advanced combustion technology, and elegant design, it transforms any standard fireplace into the heart of your home during winter months. This fireplace insert not only enhances indoor comfort but also adds a timeless element to your living space, making it a worthwhile investment for homeowners.
Top Page Image Contents