Faber PRS20 Important Safety Advice, Electrical, General, Installation, Manual & Remote Operation

Page 4

- 1 -

UK

IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLYAND RETAINED FOR FUTURE REFERENCE

Important Safety Advice:

When using electrical appliances, basic precautions should be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

If the appliance is damaged, check immediately with the supplier before installation and operation.

Do not use this heater in the immediate surroundings of a bath, shower or swimming pool.

Do not use outdoors.

This heater must not be located immediately above or below a fixed socket outlet or connection box.

Do not cover or obstruct in any way the heat outlet grille located underneath the heater. Overheating will result if the heater is accidentally covered.

In the event of a fault unplug the heater.

Unplug the heater when not required for long periods.

The supply cord must be placed on the right hand side of the heater away from the heat outlet underneath the heater.

Although this heater complies with safety standards, we do not recommend its use on deep pile carpets or on long hair type of rugs.

This appliance is not intended for use by children or other persons without assistance or supervision if their physical, sensory or mental capabilities prevent them from using it safely. Children should be supervised to ensure that they do not play with the appliance.

The appliance must be positioned so that the plug is accessible.

If the supply cord is damaged it must be replaced by the manufacturer or service agent or similarly qualified person in order to avoid a hazard.

WARNING: IN ORDER TO AVOID OVERHEATING, DO NOT COVER THE HEATER.

The heater carries the Warning symbol, indicating that it must not be covered.

WARNING: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched

on and off by the utility.

Electrical

WARNING – THIS APPLIANCE MUST BE EARTHED

This heater must be used on an AC ~ supply only and the voltage marked on the heater must correspond to the supply voltage.

Do not switch the appliance on until properly installed. Please read all the safety warnings and operating instructions.

General

Unpack the heater carefully and retain the packaging for possible future use, in the event of moving or returning the fire to your supplier.

Contents of Carton.

Heater.

Wall fixing bracket.

Fixing screws and wall plugs.

Remote control and batteries (2 AAA’s type).

Spare bulb.

Do not connect the heater to an electricity supply until it is installed on a wall correctly. - see ‘Installation’.

A choice of 1kW or 2kW heat output is provided by the fan heater, which is concealed underneath the unit.

The heater can be used remotely or manually. - see ‘Operation’. General features of remote control are:

Heat output can be increased or decreased according to your particular requirements.

The illumination of fuel effect can be increased or decreased.

Please note: Used in an environment where background noise is very low, it may be possible to hear a sound which is related to the operation of the flame effect. This is normal and should not be a cause for concern.

Installation

Do not connect appliance until properly fixed to the wall and the Instruction leaflet is read fully.

The minimum distances must be observed.

For installation of the appliance, care must be taken not to damage concealed cables.

Please be careful while drilling the holes.

This model is designed to be permanently fixed to a wall at a minimum height of 300mm.

The wall bracket must be fitted horizontally and the cable routed to the bottom right of the heater as in Fig. 1.

A height of 600mm from bottom of heater to floor is recommended for optimum viewing of fuel bed (see Fig. 2 for recommended fixing dimensions).

For optimum viewing mark the top two screw fixing positions on wall in accordance with the recommended fixing dimensions - see Fig. 2.

Fix the wall bracket using the two plugs and screws provided - see Fig. 3.

Carefully lift the heater up ensuring that the top rear ledge of heater engages the wall bracket and is sitting centrally positioned. - see Fig. 4

(b).

Rotate the bottom fixing bracket down. - see Fig. 4 (c). Gently bring the heater level with the wall. - see Fig. 4 (d).

Mark the bottom hole position (see Fig. 5), remove the heater ensuring that the bottom fixing bracket is rotated up.

Drill and fit wall plug.

Refit the heater to the wall fixing bracket (i.e. follow steps as in Fig. 4 a, b, c and d) and rotate the bottom fixing bracket down again and use the screw provided to permanently fix the heater in place.

The heater should not be connected until the instruction leaflet is read fully.

Manual & Remote Operation

Setting

Operation

Setting

Flame Effect

 

Bottom Neon

Flame Effect & 1Kw Heat

Press the ‘ I ’ button

Middle Neon

Flame Effect & 2Kw Heat

Press the ‘ I ’ button again

Top Neon

The switches are located at the right hand side of the heater. The Standby switch must first be turned ‘ON’ to operate the heater manually or by remote control.

Note: It takes some time for the receiver to respond to the transmitter. DO NOT PRESS the buttons more than once within two seconds for correct operation.

To go to the previous settings press the O button.

Pressing the O button on the remote turns off the light & heat settings. To resume press the I button until the desired setting is reached - see Fig. 8.

To increase or decrease the brightness of the flames, use the dimmer button or the button on the Remote Control. The heat setting will remain the same.

To turn off the power the Standby Switch must be turned ‘OFF’.

Image 4
Contents Presada PRS20 120 540 600 ‘x’ Important Safety Advice InstallationElectrical GeneralCleaning Thermal Safety Cut-outAfter Sales Service Wichtiger Sicherheitshinweis ElektrikAllgemeines WirdHandbetrieb & Fernbedienung Anweisungen zum Anbringen der KieselsteineLampen austauschen Thermal-SicherheitsabschaltungInstallatie Belangrijk VeiligheidsadviesElektrisch AlgemeenAanwijzingen voor het installeren van kiezelstenen Service na aankoopVervanging van gloeilamp Beveiliging tegen oververhittingConsigne importante de sécurité Informations électriquesInformations générales Fonctionnement manuel et à distanceMode d’emploi de l’effet charbon Remplacement des ampoulesService après-vente Disjoncteur thermiqueВажный совет по технике безопасности Электрическая частьОбщие положения МонтажРучное и дистанционное управление Èíñòðóêöèè ïî óñòàíîâêå ãàëå÷íèêàÒåïëîâûå ïëàâêèå ïðåäîõðàíèòåëè ÓòèëèçàöèÿPage DE Garantie Zárucný list

PRS20 specifications

The Faber PRS20 is a remarkable range hood that combines advanced technology with elegant design, making it an ideal addition to modern kitchens. Known for its exceptional performance and user-friendly features, the PRS20 is engineered to provide superior ventilation, ensuring a clean and fresh cooking environment.

One of the standout features of the PRS20 is its powerful motor, which delivers an impressive extraction rate. This ensures that smoke, steam, and odors are efficiently removed from your kitchen, maintaining a comfortable environment while you cook. The range hood operates at multiple speeds, allowing you to adjust the airflow according to your cooking needs. Whether you're simmering a delicate sauce or searing meat at high heat, the PRS20 has you covered.

In addition to its powerful motor, the Faber PRS20 incorporates advanced sound-absorption technology. This innovation minimizes operational noise, providing a quieter cooking experience without compromising on performance. Cooking can often be a noisy affair, but with the PRS20, you can enjoy peace of mind while preparing your meals.

The PRS20 also comes equipped with bright LED lighting, which illuminates the cooking area effectively. This not only helps in improving visibility while cooking but also adds a modern touch to the kitchen decor. LED lights are energy-efficient and have a long lifespan, making them an excellent choice for both functionality and sustainability.

Another notable characteristic of the PRS20 is its sleek and stylish design. Available in a variety of finishes, including stainless steel and glass, this range hood complements any kitchen aesthetic. Its contemporary look enhances the overall ambiance of the kitchen space, making it a focal point rather than just a functional appliance.

Installation flexibility is another asset of the Faber PRS20. It can be used in both ducted and recirculating modes, making it suitable for various kitchen configurations. The easy-to-install design means that you can customize the hood's setup to match your kitchen's layout and needs.

With its combination of powerful performance, modern aesthetics, and user-friendly features, the Faber PRS20 is an excellent choice for anyone looking to elevate their kitchen experience. Whether you're a passionate home chef or someone who enjoys occasional cooking, this range hood promises to offer both style and efficiency, making cooking a more enjoyable and pleasant experience.