Vermont Casting H33BDVRRNP Optional Accessories Available, Fan Kits, Specifications, Maintenance

Page 28

Pyromaster© H33BDVRRN/P

Optional Accessories Available

Fan Kits

FK24 Fan Assembly

This auxiliary fan system increases the efficiency of the circulation of the heated air.

The FK24 fan kit allows variable speed control of the circulation fan and also incorporates a heat sensor in the circuit.

Specifications

115 Volts / 60Hz / 56 Watts

Maintenance

The fan itself does not require regular maintenance, however periodic cleaning of the fan and the surrounding area is required.

Check the area under the control door (lower louvre assembly) and in front of the fan and wipe or vacuum this area at least once a month during the operating season.

Installation

The fan assembly and other components are supplied fully wired, eliminating the need for a licensed electrician to carry out the installation.

If hard wiring the fan in using Method B (following) we strongly recommend the use of a licensed electrician.

1.Open the lower louvre assembly. Maneuver the fan

&bracket assembly around the gas valve and lines to locate the unit onto the screw studs on the back of the fireplace.

2.Install the thermal sensor under the bottom of the firebox, locating it over the two 10 mm studs and secure it with nuts.

3.Locate the fan speed control unit. This can be fitted behind the lower louvre assembly as in Figure 43 or located remotely in a conveniently located wall mounted electrical box. Remote location of the speed control will require suitable extension of the component wiring.

4.The power supply may be connected in two ways:

Method A

Route the 6’ lead fitted to the unit to a conveniently located wall socket.

Method B (Using EB-1 Receptacle Box)

The EB-1 receptacle box (Pt. # ZA1200) may be hard wired into the house supply. The fan lead is then plugged into the EB-1 box. Refer to Page 29 for wiring the EB-1 receptacle box.

Thermal

Fan

Sensor

 

 

 

Valve

 

Fan Speed

EB-1

 

Switch

 

Receptacle

 

 

 

Gas Lines

Box

FP1222

 

 

 

Fig. 42

FK24 fan installation.

 

FK12

This auxiliary fan system increases the efficiency of the circulation of the heating air.

The FK12 Fan Assembly is a fixed speed fan system and does not allow for variable speed control. It does not use the speed control unit or the heat sensor used in the FK24 Kit.

Specifications

115 Volts / 60 Hz / 56 Watts

Maintenance

The fan itself does not require regular maintenance, however periodic cleaning of the fan and the surrounding area is required.

Check the area under the control door (lower louvre assembly) and in front of the fan and wipe or vacuum this area at least once a month during the operating season.

Installation

The fan assembly is supplied fully wired eliminating the need for a licensed electrician to carry out the installation.

1.Open the lower Louvre assembly. Maneuver the fan & bracket assembly around the gas valve and lines to locate the unit against the back wall of the appliance, resting on the base.

2.With the protective cover removed from the self- adhesive ‘Velcro’ strips apply mild pressure to the fan & bracket unit to secure the strips to the metal panels. No further securing is required.

3.Power to the fan can be supplied by plugging the supplied lead into a conveniently located wall socket or by using a hard-wired EB-1 receptacle box.

28

10004798

Image 28
Contents Builder Rear Vent Direct Vent Table of Contents Installation & Operating Instructions Locating Your FireplaceFireplace Dimensions Framing DimensionsMantels Clearance to CombustiblesHearth Gas Specifications Gas Line InstallationFraming and Finishing Final FinishingRemote ON/OFF Switch Alternate Switch LocationInstallation General Venting Information-Termination LocationCanadian Installations1 US Installations2 General Venting Information Termination LocationCanadian Installations USA InstallationsGeneral Information on Assembling DV Components Crimped End PipesTwist Lock Pipes How to Use the Vent GraphRear Wall Vent Applications Rear Wall Installations Straight VentingMaximum dimensions Vertical Sidewall ApplicationsVertical Sidewall Installations Maximum elbow usageAlways install horizontal venting on a level plane Zero clearance sleeve is only required for combustible wallsBelow Grade Installations 7DVSKSVertical Through-the-Roof Installation Vertical Through-the-Roof ApplicationsMin ’ 610 mm Twist Lock Venting Components Crimped End Venting Components Operating Instructions Log Identification Chart Flame & Temperature AdjustmentFlame Characteristics LocationLighting And Operating Instructions To Turn Off Gas To HeaterTroubleshooting Honeywell VS8421 Remove Glass Doors Before Service WorkLP Conversion Procedure Air Shutter SettingFuel Conversion Instructions LP Conversion Kit ComponentsBurner and Burner Compartment MaintenanceBrass Trim Pyromaster H33BDVRRN/P Description Part NumberH33BDVRRN/P Optional Accessories Available SpecificationsMaintenance Fan KitsEB-1 Electrical Box Wiring InstructionsCeramic Refractory Kits Do not remove the existing window frame assembly Decorative Bay WindowsRemote Controls Bay Window ScreenTrim Kit Model Functions ControlledLimited Warranty & Extended Life Time Protection

H33BDVRRN, H33BDVRRNP specifications

The Vermont Casting H33BDVRRNP and H33BDVRRN are renowned for their sophisticated design and advanced features, making them excellent choices for those seeking high-quality wood-burning stoves. These stoves are a testament to the perfection of both form and function, showcasing Vermont Casting's commitment to craftsmanship and innovation.

One of the standout features of the H33BDVRRNP and H33BDVRRN is their efficient heat output. With a robust firebox capacity, these stoves can accommodate larger logs, promoting longer burn times. This not only means less frequent tending to the fire but also enhanced heat retention in your home. They offer an impressive BTU range, ensuring that they can effectively warm a variety of spaces, from cozy cabins to expansive living rooms.

Equipped with the latest burn technology, the H33BDVRRNP and H33BDVRRN provide a cleaner, more efficient burn. The stoves utilize a secondary combustion system that significantly reduces emissions, making them an environmentally friendly option. This advanced technology optimizes fuel usage, resulting in less wood consumption and fewer pollutants released into the atmosphere. In addition, the integrated air wash system keeps the glass doors clean, allowing you to enjoy the mesmerizing view of the flames without the hassle of frequent maintenance.

The construction quality of the H33BDVRRNP and H33BDVRRN is evident throughout. Made from solid cast iron, these stoves are built to withstand the rigors of high-heat operations while providing excellent durability and longevity. The heavy-duty materials also contribute to excellent heat retention, ensuring that warmth radiates effectively throughout your home.

Aesthetically, both models boast a classic yet contemporary design, making them suitable for a wide range of interior styles. Available in various finishes, homeowners can easily find a version that complements their décor. The thoughtfully designed airflow control allows users to achieve their ideal burn rate with ease, enhancing both usability and comfort.

In conclusion, the Vermont Casting H33BDVRRNP and H33BDVRRN are exceptional wood-burning stoves that combine efficiency, beauty, and advanced technology. Their features make them a reliable heating source while maintaining a minimal environmental impact, ensuring that you can enjoy the warmth and ambiance of a wood fire without compromising on quality or sustainability.