Vermont Casting 2170 manual Reloading and Reviving a Wood Fire, Remove and Store Ash Safely

Page 21

increase over an approximate 30 minute period. The probe temperature will peak during the first 2/3 of the burn time and then fall after the volatiles have burned off. To ensure continued operation of the combustor, let the temperature approach 1000°F (540°C) before reducing the air settings.

5.Close the primary air control to a medium setting, or about 6:00 on the imaginary clock face referred to on Page 18. The fire volume will diminish immedi- ately, but the stove will continue to warm up. Main- tain control of the fire using the primary air and combustor air controls, and remember: reduce the setting for a smaller fire, increase the setting for a larger fire. Refer back to the air control settings chart on Page 18 for recommended settings at different burn rates.

DO NOT OVERFIRE THIS HEATER. Overfiring may cause a house fire, or can result in permanent damage to the stove and to the catalytic combustor. If an exterior part of the stove or the chimney connector glows, you are overfiring.

Reloading and Reviving a Wood Fire

When reloading, best results will be obtained if you first de-ash the stove by stirring the fuel bed to allow ash to fall through the grate into the ash pan.

Do not break the charcoal into very small pieces or pound or compress the charcoal bed.

It is important that air can circulate through the charcoal bed during the burn. Larger pieces of charcoal allow more air to circulate under the wood and will result in the fire reviving more quickly, and will also encourage the stove to burn more cleanly.

Open the stove damper and wait at least fifteen sec- onds for the draft to increase. Open the door slowly, add the fuel, and then close the damper. Split wood will fill the firebox more completely and reduce the fre- quency of reloading.

Leave the stove damper open for a short time until the probe temperature reaches 800°F (430°C), then close it.

Sometimes the temperature will drop below 600°F

(316°C) after reloading, particularly if the loading door is open a long time. Should the temperature drop below this level, stimulate the fire by increasing the primary air supply. Reduce the air supply when the temperature has reached 800°F (430°C).

NOTE: If the charcoal bed is relatively thick and your fuel is well-seasoned, it is possible to add fresh fuel and close the damper immediately, and adjust the air control for your desired heat output.

Dutchwest Seneca

Remove and Store Ash Safely

Check the ash pan before reloading the stove. If the ash level is close to the top, empty the pan. Before replacing the ash pan, clear away any ash that has spilled over the sides and back of the pan.

Empty the ash drawer regularly, typically everyone to three days. The frequency will vary depending on how hot you run your stove: the hotter the fire, the more wood you burn, and the faster ash will accumulate.

Ash may contain hot coals and must be treated with extreme care.

ST744

Fig. 28 Wear a heavy stove glove for protection when removing ash.

Always Dispose of Ash in a Safe Manner

Ash should be removed frequently and placed outdoors in a metal container with a tight-fitting lid. The closed container of ash should be placed on a noncombustible floor or on the ground, well away from all combustible materials, pending final disposal. If the ash is disposed of by burial in soil or otherwise locally dispersed, it should be retained in the closed container until all cinders have thoroughly cooled. Wood ash may be used as a garden fertilizer.

CAUTION: Never use a vacuum cleaner to remove ash from the stove; always remove and dispose of the ash properly.

2006063

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Seneca Accessories Table of ContentsSeneca, Model SpecificationsInstallation Chimney TypesMasonry Chimneys Assembling the Chimney Connector Chimney Connector GuidelinesPrefabricated Chimneys Chimney HeightSecuring the Connector To a Prefabricated Chimney Securing the Connector to a Masonry ChimneyFreestanding Installations Fireplace Installations Above the Fireplace Fireplace Installations Through the FireplaceWall Pass-Throughs Wall pass-through enclosed with noncombustible materials Floor ProtectionKeep the Stove a Safe Distance from Surrounding Materials Floor Protection for FireplaceSafe Ways to Reduce Clearances Wall ShieldsFireplace and Mantel Trim Shields Fireplace and Mantel Trim Clearances Heat shield, no connector Stove InstalledShields on connector1,2 Parallel to WallSeneca Clearance Diagrams Wall Shield Requirements for Common Seneca Installations InCorner Parallel to Wall Install Catalytic Probe AssemblyInstall Air Duct for Outside Air Unpack the PartsOperation Seneca Control Settings Burn Rate Primary Air Combustor Air Use the Air Control Settings That Work Best for YouHigh-Efficiency Wood Burning With Catalytic Combustion How to Build a Wood Fire Keep it GoingConditioning Your Stove Starting and Maintaining a Wood FireYou will soon find out that this stove is HOT While Reloading and Reviving a Wood Fire Remove and Store Ash SafelyAlways Dispose of Ash in a Safe Manner Maintenance Cleaning the GlassTest And Repair the Door Gaskets Repair Missing Cement in Seams Damper AdjustmentAvoid Damaging the Glass Door Panel Replace Broken Glass ImmediatelyWhen to Suspect a Combustor Problem Care of the Catalytic CombustorRemove and Inspect the Combustor Watch for Better Results Maintenance Schedule Chimney ConnectorStove Catalytic Combustor Draft Management Single Venting Draft TestingFuel CreosoteHow to Obtain Service Warranty

2170 specifications

The Vermont Casting 2170 is a remarkable wood stove that combines classic styling with modern efficiency, making it a favored choice for homeowners looking to enhance their heating options. Renowned for its performance, this wood stove stands out due to its unique blend of traditional craftsmanship and innovative technology.

One of the primary features of the Vermont Casting 2170 is its robust construction. Made from high-quality cast iron, the stove not only ensures durability but also efficient heat retention. This material allows the stove to radiate warmth long after the fire has died down, offering prolonged comfort during the coldest months. With a striking design that includes elegant arches and detailed accents, the 2170 serves as a functional art piece in any living space.

The heating capacity of the Vermont Casting 2170 is impressive, boasting an output of up to 75,000 BTUs, which can effectively heat large areas up to 2,100 square feet. This makes it suitable for both smaller homes and larger spaces needing efficient heating solutions. Its large firebox can accommodate larger logs, enabling longer burn times and reducing the frequency of loading during the evening.

Another notable feature is its advanced air intake system, which promotes efficient combustion. This system not only optimizes fuel consumption but also minimizes emissions, making the 2170 an environmentally friendly choice. Additionally, it features a secondary combustion system, ensuring that burning gases are consumed for maximum heat and minimal waste.

The Vermont Casting 2170 also incorporates a convenient, easy-to-use ash pan, allowing users to clean out ash without hassle, contributing to a more streamlined maintenance experience. With an adjustable air control mechanism, users can easily regulate the burn rate, ensuring the perfect balance between heat output and fuel efficiency.

Overall, the Vermont Casting 2170 exemplifies a perfect fusion of vintage aesthetics and contemporary technology. Its durable construction, substantial heating capacity, and environmentally conscious features make it a top choice among wood stoves, creating a warm, inviting atmosphere while also being kind to the planet. For anyone looking to invest in a wood stove that combines style, functionality, and sustainability, the Vermont Casting 2170 is a compelling option that stands the test of time.
Top Page Image Contents