Hampton Direct U32 installation manual Maintenance

Page 31

MAINTENANCE

Top View of pilot fl ame

Incorrect fl ame pattern will have small, probably yellow fl ames, not coming into proper contact with the rear of the burner or thermopile.

Top View of pilot fl ame

If you have an incorrect fl ame pattern, contact your FPI dealer for further instructions.

GENERAL VENT

MAINTENANCE

Conduct an inspection of the venting system semi-annually. Recommended areas to inspect as follows:

1)Check the Venting System for corrosion in areas that are exposed to the elements. These will appear as rust spots or streaks, and in extreme cases, holes. These components should be replaced immediately.

2)Remove the Termination Cap, and shine a fl ashlight down the Vent. Remove any bird nests, or other foreign material.

3)Check for evidences of excessive condensation,suchaswaterdropletsforming in the inner liner, and subsequently dripping out the joints, Continuous condensation can cause corrosion of caps, pipe, and fi ttings. It may be caused by having excessive lateral runs, too many elbows, and exterior portions of the system being exposed to cold weather.

4)Inspect joints, to verify that no pipe sections or fi ttings have been disturbed, and consequently loosened. Also check mechanical supports such as Wall Straps, or plumbers' tape for rigidity.

LOG REPLACEMENT

The unit should never be used with broken logs. Turn off the gas valve and allow the unit to cool before opening door to carefully remove the logs. The pilot light generates enough heat to burn someone. If for any reason a log should need replacement, you must use the proper replacement log. The position of these logs must be as shown in the diagram under Log Installation.

NOTE: Improper positioning of logs may create carbon build-up and will alter the unit’s performance which is not covered under warranty.

GOLD-PLATED TRIM

The 24 carat gold plated fi nish on the trim requires little maintenance, and need only be cleanedwithadampcloth.DONOTuseabrasive materials or chemical cleaners, as they may harm the fi nish and void the warranty. Clean any fingerprints off before turning the unit on. If the top louvers start to discolour, check the door gasket seal and replace if necessary.

DOOR GLASS

YourFPI insertissuppliedwithhightemperature, 5mmNeoceramceramicglassthatwillwithstand the highest heat that your unit will produce. If your glass requires cleaning, we recommend using an approved glass cleaner available at all authorized dealers. Do not use abrasive materials. Do not clean the glass when hot.

In the event that you break your glass by impact, purchase your replacement from an authorized FPI dealer only, and follow our step-by-step instructions for replacement.

Warning: Do not operate appliance withglasspanelsremoved,cracked orbroken.Replacementoftheglass should be done by a licensed or qualified service person.

Caution: Wear gloves when removing damaged or broken glass.

Flush Glass Replacement

Remove the fl ush door front (as per instructions in section "Standard Flush Doo"). Remove the 4 glass clips from each corner. Slide in the new replacement glass. Push the 4 glass clips back onto the frame.

GLASS GASKET

If the glass gasket requires replacement use glass gasket (Part # 936-265) for the Bay Front and a tadpole gasket for the Flush Front (Part

# 936-155).

U32-5 FPI Direct Vent Gas Insert

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents U32 Gas Insert To the NEW Owner Table of Contents Safety Label MA Code CO Detector RequirementsInstallation Clearances to Combustibles Installation ChecklistMinimum Fireplace Dimensions Manufactured Mobile Home Additional RequirementsVenting Flue Liner InstallationGAS Connection Natural Gas Propane GAS Pipe Pressure TestingGAS Insert Aeration System Optional Brick Panel27-32 27-33 27-31 LOG SET Installation27-33 27-35 27-31 27-36 27-33 Completed Log Set Installation Rear View Trim Assembly Diagram Regency Faceplate Trim InstallationRear View Faceplate Assembly Diagram Flush Louvers Standard Flush DoorOptional Double Screen Doors Optional Flush TrimRemoving Bay Door BAY LouversOptional BAY Door Optional BAY TrimFor P36D-1 / P36-4 Only Conversion KIT #514-969 from NG to LPInstallation of the DC Sparker Chain Full Screen Doors Hinge Switch Box Assembly Boss on rear left side piece Hampton Cast Faceplate InstallationEnsure that Top and sides are Aligned U32 Grill Stop Bracket Hampton Cast Grill InstallationSlide side fi ller bracket Side Hook SlotsLeft Side Kensington Front InstallationPin on Door Frame Kensington Panel Door InstallationOptional Wall Thermostat Optional Remote ControlThermostat Wire Table KensingtonElectrical Grounding Instructions Wiring DiagramsFor Propane Units and Units Equipped with DC Spark Boxes Operating Instructions Copy of Lighting Instruction Plate Maintenance InstructionsMaintenance Bay Glass Removal FAN MaintenanceShut off the gas supply Valve ReplacementEntrire assembly out Install a new gasket and reinstall the valve assemblyMain Assembly Parts ListBurner Assembly & LOG SET Flush Door Bay Door400-917 Faceplate Assembly402-918 Complete Faceplate Set Hampton Cast Faceplate Assembly Conditions WarrantyInstaller Please complete the following information

U32 specifications

Hampton Direct U32 is a versatile and innovative product designed to enhance everyday living. This device serves as an all-in-one solution, combining functionality, convenience, and modern technology to meet the needs of today's consumers.

One of the standout features of the Hampton Direct U32 is its user-friendly interface. The device comes equipped with a high-resolution touchscreen display, allowing users to navigate through various functions effortlessly. This intuitive design ensures that individuals of all ages can operate the U32 without frustration or difficulty.

The U32 also boasts a range of connectivity options, including Bluetooth and Wi-Fi capabilities. This enables users to connect the device to their smartphones, smart home systems, or other peripherals, making it a seamless addition to any tech-savvy lifestyle. With the ability to sync with mobile applications, users can access a broad range of features, from remote control functions to personalized settings tailored to their preferences.

In addition to connectivity, the Hampton Direct U32 incorporates advanced technology such as voice recognition. This feature allows users to control the device hands-free, enhancing convenience and providing an intuitive experience. The voice command functionality can access various features, further simplifying routine tasks and fostering a more connected environment.

Moreover, the U32 is designed with energy efficiency in mind. Utilizing modern energy-saving technologies, this device minimizes power consumption while delivering reliable performance. It is not just about functionality; the U32 is built to be eco-friendly, appealing to environmentally conscious consumers who wish to reduce their carbon footprint.

Another remarkable characteristic of the Hampton Direct U32 is its durability. Constructed from high-quality materials, the device is designed to withstand daily wear and tear while maintaining optimal performance. This robustness ensures that users can rely on the U32 long-term, making it a worthwhile investment.

Overall, the Hampton Direct U32 stands out as a multifunctional device that combines cutting-edge technology, user-friendly design, and energy efficiency. It successfully addresses the demands of modern living by offering robust features that cater to convenience, connectivity, and sustainability, making it an essential tool for households looking to simplify and enhance their daily routines.
Top Page Image Contents