INSTALLATION
IMPORTANT:
SAVE THESE
INSTRUCTIONS
The Regency Gas Fireplace must be installed in accordance with these instructions. Care- fully read all the instructions in this manual first. Consult the building authority having jurisdic- tion to determine the need for a permit prior to starting the installation.
Note: Failure to follow these instruc- tions could cause a malfunction of the heater which could result in death, serious bodily injury, and/ or property damage. Failure to follow these instructions may also void your fire insurance and/or warranty.
FOR YOUR SAFETY
This appliance requires air for proper combus- tion. Always provide adequate combustion and ventilation air. Follow instructions and information in the current CAN/CGA B149 (in Canada) or the current National Fuel Gas Code ANSI Z223.1 (in the USA), regarding require- ments for combustion and ventilation air.
GAS PIPE TESTING
The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig. (3.45 kPa).
SPECIFICATIONS
Fuel: Natural gas or Propane
Electrical: 120V A.C. system.
Fan/Blower: Variable speed, 125/75 CFM.
Log Sets: Ceramic fiber, 3 per set.
Vent System: Listed minimum 4"
INSTALLATION INTO A
FACTORY BUILT
FIREPLACE
The ULTIMATE Gas Inserts have been tested and approved to be vented into any approved Factory Built Fireplace that will allow the Insert to physically fit into the firebox. A Factory Built
Fireplace Trim Kit, Part #
If the factory built fireplace height is too
low for your Insert, you may remove the
smoke shelf, baffle plate, and damper
plate from the factory built fireplace if
removable without cutting or torching,
as long as these items are saved and are
removed.
INSTALLATION INTO ZERO CLEARANCE FIREPLACES
The ULTIMATE Gas Inserts are only approved
for installation into the ULTIMATE Gas
Insert Zero Clearance Fireplace Kit, mod-
el #
BEFORE YOU START
Safe installation and operation of this appliance requires common sense, however, we are required by the Canadian Safety Standards and ANSI Standards to make you aware of the following:
General Safety Information
1)The appliance installation must conform with local codes or in the absence of local codes, with current CAN/CGA B149 (in Canada) or the current National Fuel Gas Code ANSI Z223.1. This appliance MUST be installed by a qualified gas fitter technician only.
2)Installation and repair should be done by a qualified service person.
3)The appliance should be inspected before use and at least annually by a professional service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is imper- ative that control compartments, burners and circulating air passageways of the appliance be kept clean and free from excessive lint from carpeting.
4)See general construction and assembly instructions. This appliance may only be installed in a vented,
5)This appliance is Listed for bedroom instal- lations when used with a Listed Millivolt
Thermostat. Some areas may have further requirements, check local codes before installation.
6)This unit is not approved for installation into a mobile home.
7)Always connect this fireplace to a chimney and vent to the outside of the building envelope. Never vent to another room or inside a building. Make sure that the vent is properly sized and is of adequate height to provide the proper draft.
8)Inspect the venting system annually for blockage and any signs of deterioration.
9)Any safety glass removed for servicing must be replaced prior to operating the appliance.
10)To prevent injury, do not allow anyone who is unfamiliar with the operation to use the fireplace.
11)Due to high temperatures, the appliance should be located out of high traffic areas and away from furniture and draperies. Children and adults should be alerted to the hazards of high surface temperatures, especially the fireplace glass and gold trims, and should stay away to avoid burns or clothing ignition. Young children should be carefully supervised when they are in the same room as the appliance. Clothing or otherflammablematerialshouldnotbeplaced on or near the appliance.
12)WARNING: Failure to position the parts in accordance with the diagrams in this manual or failure to use only parts specifically approved with this appli- ance may result in property damage or personal injury.
13)WARNING: Operation of this appliance when not connected to a properly installed and maintained venting system or tamper- ing with the blocked vent
14)This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.
Emissions from burning wood or gas could contain chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
MATERIALS
REQUIRED
No electrical power supply is required for the gas control to operate. A 120 Volt AC power
Regency | 5 |