Regency Wraps Z2510L installation manual SET Warmhearth Into Position, Installing Chimney System

Page 11

INSTALLATION

result if stand-offs are not properly installed.

IMPORTANT:Insulationextendsfor- ward to seal against the back of the WarmHearth masonry or non-com- bustible face.

SET THE

WARMHEARTH

INTO POSITION

1)Estimate the total weight of the fireplace system and surround materials such as brick, stone, etc., to be installed. Shipping weight is 715 lbs. and stripped weight is 460 lbs. Stripped weight refers to the weight of the product with bricks, door and any accessories removed.

2)Measure the square footage of the floor space to be occupied by the system, surrounds and hearth extensions.

3)Note the floor construction, i.e. 2 x 10’s, (51 x 250 mm), single or double joists, type and thickness of floor boards and consult your local building code to determine if you need additional support.

4)Remove door, firebox bricks, louvers etc.

Note: Set aside Gold doors and louvers away from harsh chemicals and away from abrasive materials to avoid damage, e.g. muriatic acid for masonry wash will strip the gold plate on the door. Firebricks are fragile and should be handled with caution.

The fireplace may be installed directly on a combustible floor or raised on a platform of an appropriate height. Do not place fireplace on carpeting, vinyl or other soft floor coverings. It may, however, be placed on flat wood, ply- wood, particle board or other hard surfaces. Be sure the fireplace rests on a solid contin-

uous floor or platform for support and to pre- vent cold air from entering the room from under the fireplace, if against an outside wall.

The fireplace may be positioned and then the framing built around it, or the framing may be constructed and the fireplace positioned into the opening.

The minimum ceiling height is 7 feet. When the unit is raised 4 inches above the floor the Regency Hearth Extension (Part# 000-910) is not required. A suitable non-combustible hearth pad is mandatory in all installations.

INSTALLING THE

CHIMNEY SYSTEM

Following are a set of general guidelines for installation of the chimney system. The more detailed installation manual supplied with the specific chimney system must be followed.

1)Using standard construction framing tech- niques, construct the opening for the chim- ney route up through the ceiling(s) and roof or through an outside chase. Framing must maintain adequate minimum air space clear- ance at all times.

CAUTION: Allow a minimum 2 in. chimney air space or as specified by the owner's manual for the chimney, to combustible framing members throughout vertical or offset chimney installation.

2)Attach anchor plate/fireplace adaptor to the top of the fireplace. It is important that a tight seal be made with this part and the unit’s collar. This must be purchased with the chimney system.

3)Install firestop, radiation shield, or attic insu- lation shield as required at each floor penetration. See Table 1. Check chimney manufacturer's framing opening sizes to allow for correct clearances. All parts must be listed.

4)The roof flashing should be installed making sure that alignment is correct with openings below.

5)Chimney lengths may now be added until the required height is reached. A minimum flue height of 16 ft. from the floor (or 12 ft. from the top of the unit) is mandatory. Please refer to Table 2 for Flue Heights:

The performance of your unit is governed to a very large extent by the chimney system. Too short a chimney can produce poor drafting which in turn can cause difficult start-up, dirty glass, smoking out door and even reduced heat output. Too tall a chimney may prompt excessive draft which can result in very short burn times

and excessive heat output. The chimney must extend at least 3 ft. above its point of penetration of the roof and be at least 2 ft. higher than any point on the roof, wall, or building within 10 ft. of it.

6)The raincap and storm collar should now be fastened to the top of the chimney. Install additional support(s) as indicated by chim- ney manufacturer's instructions.

SPECIAL NOTES:

1)Negative Pressure In The House. When there is no fire in your unit there still should be sufficient draft to draw smoke from a burning piece of paper held under the baf- fle. If your installation is correct, smoke will go up the flue. If however, there is a problem with your installation, cold air may be coming down the flue into the room. This may be the case if your unit smokes on start-up with the door open, until the unit heats up. To overcome this problem, try closing an upstairs window and open a nearby window to pressurize the house. Note: the door can be open briefly to start your fire but must be closed during reg-

Regency Z2510 WarmHearth

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents WarmHearth Fireplace Regency Fireplace Product Table of Contents Copy of Safety Label for Z2510L Safety LabelOptions InstallationRegency Warmhearth Product DetailsImportant Please read and follow these rules for safety Dimensions and SpecificationsFireplace Enclosure Framing Clearances Height RequirementsThereafter and no stand-offs are required Location FireplaceHearth Extension Entire enclosure floor, wallCanada Chimney System ConsiderationsChimney Height Chase EnclosureBefore YOU Start Installing STAND-OFFSInstallation Components SET Warmhearth Into Position Installing Chimney SystemDo not use water, it will create a steam explosion Offset Chimney InstallationModel 1st Floor 2nd Floor into Attic Internal Blower with Thermo-Disc Installing Outside AIR KITWiring the Warmhearth Installing the Blower SystemsInternal and External Blowers With a Thermodisc Parts ListGravity AIR Feed KIT Option External Blower with Thermo-DiscMaterials Required Installing Your Central Heating SystemTypical Floor Register Masonry Retainer Kit Option Non-Self Supporting, Thin Veneer Facades InstallationFinishing Warmhearth Completing the FacingExample Face of Fireplace Flush with Wall Sheathing Finishing DetailsCompleting the Mantle Masonry Liner Bricks Latch AdjustmentGlass Installation Secondary AIR Tube InstallationMaintenance MaintenanceSafety Guidelines Parts LIST- Firebox & Body Parts ListParts LIST- BAFFLES, DOOR, Options Warranty Lifetime WarrantyInstaller Please complete the following information

Z2510L specifications

The Regency Wraps Z2510L is a standout product in the realm of kitchen essentials, designed with both functionality and aesthetics in mind. This versatile wrap features a range of characteristics that make it an ideal choice for culinary enthusiasts and professional chefs alike.

One of the main features of the Z2510L is its generous length, which measures 25 feet. This prolonged size allows users to wrap a variety of foods, from large cuts of meat to multiple servings of leftovers, without the hassle of using multiple pieces. The wrap's construction includes a durable, high-quality material that is not only strong and puncture-resistant but also maintains its elasticity when stored, ensuring longevity and reliability for repeated use.

In terms of technology, the Z2510L employs a unique non-stick surface that prevents food from sticking to the wrap, allowing for easy removal and presentation. This is particularly beneficial for delicate items such as pastries or roasted vegetables, ensuring that meals are served beautifully without compromising on taste or texture. Moreover, the wrap is microwave-safe, making it an excellent choice for reheating food without the risk of melting or chemical leaching, a common concern with lower-quality wraps.

Another characteristic that sets the Regency Wraps Z2510L apart is its ease of use. The roll is designed with a convenient dispenser that allows for controlled tearing, minimizing waste and maximizing efficiency in the kitchen. This thoughtful design feature is particularly advantageous in busy cooking environments where time is of the essence.

The Z2510L is also environmentally conscious, as it is made from materials that are biodegradable and free from harmful chemicals, appealing to eco-friendly consumers looking to reduce their environmental footprint.

In summary, the Regency Wraps Z2510L combines practicality, quality, and a commitment to sustainability, making it a must-have in any kitchen. Its standard features, user-friendly technology, and eco-conscious materials reflect a modern approach to food storage that meets the demands of today's consumers. Whether it's for wrapping, storing, or reheating, the Z2510L is engineered to uplift the culinary experience, ensuring that both home cooks and professional chefs have the best tools at their disposal.
Top Page Image Contents