Lopi Freedom Bay Fireplace Insert owner manual Surround Panels, Installation Instructions

Page 31

Optional Equipment

31

Surround Panels

NOTE: Install the door shell (and side frames) prior to installing the surround panels.

SURROUND PANEL SIZE

HEIGHT

WIDTH

PART #

8"

29-1/2"

45-3/8 "

99300293

10"

31-1/2"

49-3/8 "

99300294

12"

33-1/2"

53-3/8 "

99300295

Installation Instructions

Stove Top

ab

1. With the insert 12” from the

fireplace, install the side

surround panels (see the

directions to the right).

2. Adjust the position of the

side panels so they are: 1)

flush with the bottom of the

insert; 2) both the same

distance back from the

front of the insert; 3)

perpendicular to the floor

(use the top panel, if

necessary, to judge

alignment). Tighten the

screws that hold the side

panels in place.

3. Place the insert into the

fireplace and connect the

flue (if using a positive or

direct connection). Install

the top panel and trim

following the directions

Rotate the panel back

Place two U-Nuts (included

and place it so the inside

with the insert) over the inside

flange fits inside the side

flange on one of the side

convection jacket. Note

surround panels (flat side in).

how the stove top fits

 

 

into the notch.

 

Notch

 

 

 

 

 

 

Back Side

of Side

Surround

Panel

The flat side faces inwards.

Top of Insert

Side

Convection

Jacket

c

5/16"Nutdriver

Attach the side panels with the two screws included with the insert. The screws pass through the side convection jacket and attach to the U-Nuts. Do not tighten the screws fully until the panels are aligned.

below.

Insulation Installation

(required only for face seal installations)

1.With the insert drawn 6" from the fireplace, glue the insulation strip included with the insert to the back of the panels using RTV silicon or stove gasket cement. The insulation should be installed so it overlaps the fireplace opening to form a seal between the panels and the fireplace face. Let the silicon or cement dry.

Spring

Clips

Top

Install the top panel so the tabs insert into the joggle clips on the top panel

Micro (1/16”)

Standard

Screwdriver

Top Trim

"L" Bracket

Right Side

Trim

Optional Trim Installation: Insert one leg of each "L" bracket into the top and side trim piece. Align the trim to form a precise corner, then tighten the two set screws with a small standard screwdriver. Slide the trim over the panels. Place the spring clips behind the panels at the locations shown. This keeps the trim tight against the panel. Optional Knock-Out An optional knock-out is provided on both sides if the power cord is routed behind the surround panel.

2.Push the insert into the fireplace, allowing the insulation to form a seal between the panels and the fireplace. Use a screwdriver to tuck any exposed insulation behind the panels.

© Travis Industries

100-01163

4041129

Image 31
Contents Freedom Bay Fireplace Insert 2Introduction Mail your Warranty Card Today, and Save Your Bill of SaleIntroduction Important Information Table of Contents Ashes Safety PrecautionsMobile Travis Industries, Inc. grants no warranty, implied orFeatures & Specifications Installation Considerations Planning The InstallationPreparation for Installation Additional Accessories Needed for InstallationFireplace Requirements Minimum Fireplace SizeHearth Requirements Insert Placement RequirementsMasonry Fireplace Requirements Blower Installation Leveling Bolt InstallationDrafting Performance Block-Off Plate Template Block-Off Plate InstallationInsert with Direct Connection Insert with Positive ConnectionInsert with Face Seal Connection Opening the Door Safety NoticeOperating Your Appliance Before Your First FireBypass Operation Starting a Fire Approximate Air Control Settings Adjusting the Burn RateAsh Removal Normal Operating Sounds Blower OperationRe-Loading the Stove Overnight BurnSelecting Wood Testing Wood MoistureWhy Dry Wood is Key Hints for BurningTroubleshooting Remove Ash if necessary Daily Maintenance while stove is in useClean the Glass if necessary Maintaining Your ApplianceDoor and Glass Inspection Monthly Maintenance while appliance is in useCreosote Formation and Need for Removal Firebrick and Baffle Inspection Yearly MaintenanceCleaning the Air Duct and Blower Touch Up PaintReplacing the Door Handle Door PartsReplacing the Glass Replacing the Door GasketFloor and Side Firebrick Firebox PartsAir Tube Removal & Replacement Baffle Removal & ReplacementYears 6 & 7 Coverage Parts only Limited 7 Year WarrantyYears 1 & 2 Coverage Parts & Labor Years 3 Through 5 Coverage Parts & LaborListing Label Listing LabelOptional Equipment Door Shell InstallationSocket Side Frame Surround Panels Installation InstructionsInsulation Installation Required only for face seal installationsIndex