Lopi DVL Insert EF II Installation Without Surround Panels, Surround Panel Installation

Page 18

18

Installation (for qualified installers only)

Installation Without Surround Panels

The insert may be installed without surround panels. Mount the on/off switch and rheostat to the control panel under the burner pan (see “Installation of the On/Off Switch and Rheostat” on page 19).

Surround Panel Installation

PANEL SIZE

WIDTH

HEIGHT

PART #

8" x 10" Rectangular

44-3/16"

33-3/8"

98500606

Arched (8” x 10”)

44-3/16"

33-3/8"

98500608

10” x 13” Rectangular

48-3/16"

36-3/8"

98500607

1Follow the directions below to install the side panels.

a

Pre-thread the holes on the surround

 

panels with the screws included in the

 

surround panel kit.

 

5/16" Nutdriver

b

Line up each side surround panel and insert two screws from the inside to secure in place.

Run the rheostat wires, on/off switch wires, and power cord through the access hole on the insert

2Follow the directions below to install the top panel.

 

 

 

The insulation included with the

 

 

Top Trim

panels may be discarded.

 

 

 

NOTE:

 

 

b

These 3/8"

Top

 

Panel

 

 

stand-offs are

 

 

 

 

 

not required

 

 

 

and may be

flattened.

 

"L" Bracket

 

Slot for on/off

 

switch and hole

a

for rheostat

 

Install the top panel so the

Right Side Trim

 

two tabs insert into the slots

 

on the side panels.

 

Construct the panel trim. Insert one leg of each "L" bracket into the top and side trim piece. Align the trim to form a precise corner, then tighten the two set screws with a small standard screwdriver. Slide the trim over the panels.

Tighten the set screws from the back side with a small standard screwdriver

Top Trim

"L" Bracket

Right Side

Trim

© Travis Industries

4060111

100-01174

Image 18
Contents DVL Insert EF Travis Industries, IncSave Your Bill of Sale 2IntroductionIntroduction Important Information 4060111Table of Contents Safety Precautions If YOU Smell GASDo not place anything inside Dimensions Features Installation OptionsHeating Specifications Natural Gas PropaneInstallation for qualified installers only Top Convection Deflector Fireplace RequirementsHearth Requirements Leveling BoltsFactory-Built Metal Wood-Burning Fireplace Requirements Clearances Mantel ClearancesFace Sizing Face Height WidthGas Line Requirements Gas Line LocationGas Inlet Pressure Vent Requirements Altitude ConsiderationsVent Installation Vent RestrictorVent Configurations Inlet & Exhaust Re-Line Vent LocationVent Connector Removal and Installation Vent Connector Removal Installation Without Surround Panels Surround Panel InstallationInstallation of the On/Off Switch and Rheostat Electrical ConnectionFinalizing the Installation Glass Frame Removal and InstallationFinalizing the Installation Log Set Installation Install the logsInstall the twigs, ember chunk, kibbles, and rock wool Installing the Rock WoolSteps for Finalizing the Installation Air Shutter AdjustmentPilot Flame Inspection Fine Tuning the EMBER-FYRE Burner 26Operation Before You BeginLocation of Controls Operation Starting The Pilot FlameStarting the Heater for the First Time Adjusting the Flame Height28Operation Turning the Heater On and OffNormal Operating Sounds Adjusting the Blower SpeedOperation29 Normal Operating Odors30Maintenance Yearly Service ProcedureMaintaining Your Heaters Appearance Maintenance Troubleshooting TableWhat Turns the Main Burners On and Off 32MaintenanceHow this Heater Works What Prevents Gas BuildupMaintenance33 Wiring DiagramReplacement Parts List Safety Label Safety LabelYears 3 Through 5 Coverage Parts & Labor Limited 7 Year WarrantyYears 1 & 2 Coverage Parts & Labor Years 6 & 7 Coverage Parts onlyBurner Replacement LP Conversion InstructionsOptional Equipment for qualified installers only Follow the directions below to replace the orificesTo adjust the pilot flame, turn this screw Note if totally Firebacks Optional Equipment for qualified installers only Important Installation Note for Models Using the Firebacks Accent LightAccent Light Operation Lower Surround Panel Index

DVL Insert EF II specifications

The Lopi DVL Insert EF II is a remarkable heating solution that combines advanced technology with elegant design. As a part of Lopi’s prestigious line of gas inserts, the DVL Insert EF II is specifically engineered to provide efficient and reliable heating for homeowners. With an array of features, it stands out as an optimal choice for those looking to enhance their living space while maintaining energy efficiency.

One of the main features of the DVL Insert EF II is its exceptional heating efficiency. This insert is designed to provide a high heat output while minimizing energy consumption. With an impressive thermal efficiency rating, it significantly reduces heating costs and ensures that your home remains warm and inviting during the colder months. The insert is capable of heating areas up to 1,800 square feet, making it ideal for both large and small rooms.

The DVL Insert EF II boasts an advanced direct vent technology, which allows for efficient combustion while maintaining indoor air quality. This technology facilitates the intake of external air for combustion, ensuring that exhaust gases are safely vented outside, hence creating a clean and safe environment indoors. Additionally, this direct vent system enables flexible installation options, making it adaptable to various home layouts.

Another significant characteristic of the DVL Insert EF II is its impressive design. The insert features a contemporary aesthetic with clean lines and large viewing glass, allowing for an unobstructed view of the flame. The realistic flame effects and ember bed create a warm ambiance, making it a focal point in any room. Homeowners can also choose from various finishes and decorative options, ensuring that the insert complements their home decor.

Equipped with user-friendly controls, the DVL Insert EF II allows for easy adjustment of flame height and heat output. The intuitive remote control provides added convenience, enabling users to manage their comfort with just the touch of a button. Additionally, the insert is designed for easy maintenance, featuring removable components that simplify cleaning and upkeep.

In summary, the Lopi DVL Insert EF II exemplifies efficiency, elegance, and innovation. With its high thermal efficiency, direct vent technology, and stylish design, this gas insert is an excellent investment for any home. It not only provides warmth and comfort but also enhances the aesthetic appeal of your living space while promoting energy efficiency. Experience the warmth of the Lopi DVL Insert EF II and transform your home into a cozy retreat.