Lopi DVL Insert EF II owner manual 26Operation, Before You Begin, Location of Controls

Page 26

26Operation

Before You Begin

Read this entire manual before you use your new heater (especially the section "Safety Precautions" on pages 4 & 5). Failure to follow the instructions may result in property damage, bodily injury, or even death.

Location of Controls

The Pilot Flame can be

found below the back log.

OFF

Blower Knob is

HI

LO

located either on the

upper right of the

 

 

surround panels or

 

behind the access panel

An instruction card for

 

operating the fireplace is

Open the

access door

attached to the inside of the

to view the

fireplace here. Replace it for

controls.

 

easy reference.

 

Gas Control Valve

Gas Control Knob Flame Adjust Knob

PILOT

IGNITER

PIlot Igniter

is located under this plate. It can only be

accessed with the glass removed.

N

O

OFF

ON/OFF Switch is

located either on

the upper right of

the surround panels

or behind the

access panel

Blower Knob

This knob controls the speed of the internal convection blower that

 

pushes the heated air into the room.

 

On/Off Switch

This control is used to turn the heater on and off.

 

Pilot Igniter

The pilot igniter is used only to start the pilot. When pressed, it sends an

 

electrical charge to the pilot assembly. This creates a blue spark

 

 

directly next to the pilot, igniting the pilot flame.

 

Gas Control Knob

This knob is used to control gas to the heater and for starting the pilot.

 

There are three positions, ON, OFF, & PILOT. The pointer to the left of

 

the knob indicates the position this knob is in.

 

Flame Adjust Knob

This knob controls the flame height from low ("LO") to high ("HI").

The

 

pointer above the knob points to the position this knob is in.

 

 

 

 

© Travis Industries

4060111

100-01174

Image 26
Contents DVL Insert EF Travis Industries, IncSave Your Bill of Sale 2IntroductionIntroduction Important Information 4060111Table of Contents Safety Precautions If YOU Smell GASDo not place anything inside Dimensions Features Installation OptionsHeating Specifications Natural Gas PropaneInstallation for qualified installers only Top Convection Deflector Fireplace RequirementsFactory-Built Metal Wood-Burning Fireplace Requirements Hearth RequirementsLeveling Bolts Clearances Mantel ClearancesFace Sizing Face Height WidthGas Inlet Pressure Gas Line RequirementsGas Line Location Vent Requirements Altitude ConsiderationsVent Installation Vent RestrictorVent Configurations Inlet & Exhaust Re-Line Vent LocationVent Connector Removal and Installation Vent Connector Removal Installation Without Surround Panels Surround Panel InstallationInstallation of the On/Off Switch and Rheostat Electrical ConnectionFinalizing the Installation Glass Frame Removal and InstallationFinalizing the Installation Log Set Installation Install the logsInstall the twigs, ember chunk, kibbles, and rock wool Installing the Rock WoolPilot Flame Inspection Steps for Finalizing the InstallationAir Shutter Adjustment Fine Tuning the EMBER-FYRE Burner Location of Controls 26OperationBefore You Begin Operation Starting The Pilot FlameStarting the Heater for the First Time Adjusting the Flame Height28Operation Turning the Heater On and OffNormal Operating Sounds Adjusting the Blower SpeedOperation29 Normal Operating OdorsMaintaining Your Heaters Appearance 30MaintenanceYearly Service Procedure Maintenance Troubleshooting TableWhat Turns the Main Burners On and Off 32MaintenanceHow this Heater Works What Prevents Gas BuildupReplacement Parts List Maintenance33Wiring Diagram Safety Label Safety LabelYears 3 Through 5 Coverage Parts & Labor Limited 7 Year WarrantyYears 1 & 2 Coverage Parts & Labor Years 6 & 7 Coverage Parts onlyBurner Replacement LP Conversion InstructionsOptional Equipment for qualified installers only Follow the directions below to replace the orificesTo adjust the pilot flame, turn this screw Note if totally Firebacks Optional Equipment for qualified installers only Important Installation Note for Models Using the Firebacks Accent LightAccent Light Operation Lower Surround Panel Index

DVL Insert EF II specifications

The Lopi DVL Insert EF II is a remarkable heating solution that combines advanced technology with elegant design. As a part of Lopi’s prestigious line of gas inserts, the DVL Insert EF II is specifically engineered to provide efficient and reliable heating for homeowners. With an array of features, it stands out as an optimal choice for those looking to enhance their living space while maintaining energy efficiency.

One of the main features of the DVL Insert EF II is its exceptional heating efficiency. This insert is designed to provide a high heat output while minimizing energy consumption. With an impressive thermal efficiency rating, it significantly reduces heating costs and ensures that your home remains warm and inviting during the colder months. The insert is capable of heating areas up to 1,800 square feet, making it ideal for both large and small rooms.

The DVL Insert EF II boasts an advanced direct vent technology, which allows for efficient combustion while maintaining indoor air quality. This technology facilitates the intake of external air for combustion, ensuring that exhaust gases are safely vented outside, hence creating a clean and safe environment indoors. Additionally, this direct vent system enables flexible installation options, making it adaptable to various home layouts.

Another significant characteristic of the DVL Insert EF II is its impressive design. The insert features a contemporary aesthetic with clean lines and large viewing glass, allowing for an unobstructed view of the flame. The realistic flame effects and ember bed create a warm ambiance, making it a focal point in any room. Homeowners can also choose from various finishes and decorative options, ensuring that the insert complements their home decor.

Equipped with user-friendly controls, the DVL Insert EF II allows for easy adjustment of flame height and heat output. The intuitive remote control provides added convenience, enabling users to manage their comfort with just the touch of a button. Additionally, the insert is designed for easy maintenance, featuring removable components that simplify cleaning and upkeep.

In summary, the Lopi DVL Insert EF II exemplifies efficiency, elegance, and innovation. With its high thermal efficiency, direct vent technology, and stylish design, this gas insert is an excellent investment for any home. It not only provides warmth and comfort but also enhances the aesthetic appeal of your living space while promoting energy efficiency. Experience the warmth of the Lopi DVL Insert EF II and transform your home into a cozy retreat.