Southwest Specialty Products 42, 48, 36 Part Preparation, Clearances, Firebox

Page 4

CAUTION: All gas piping and connections must be tested for leaks-before the installation is completed. After ensuring that the gas valve is on, apply a soap and water solution to all connections and joints. If bubbles appear, leaks can be detected and corrected. DO NOT USE AN OPEN FLAME FOR LEAK TESTING AND DO NOT OPERATE ANY APPLIANCE IF A LEAK IS DETECTED.

36”- 52” from corner 42”- 65” from corner 48”- 70” from corner

36”- 73 1/2” - 42”- 91 1/2” - 48”- 99 1/2”

Depth of firebox

Sonoran 36

24 ½”

Sonoran 42

24 ½”

Sonoran 48

24 ½”

Width of firebox

Sonoran 36

45”

Sonoran 42

51”

Sonoran 48

57”

CLEARANCES

MINIMUM CLEARANCES TO COMBUSTIBLES ARE:

Enclosure:

0" from side of unit to framing

2" from top of unit to combustables 0.5" from back of unit to combustables

In front:

5" from fireplace opening to side wall 12" from Fireplace opening to Mantel 7" from fireplace opening to Top Trim 3" from fireplace opening to side trim

Floor:

No thermal protection required

-Floor in front flush to fireplace opening

-0" to combustable Floor under unit

Part Preparation

Inspect all parts & using scraper or painter’s tool, clean part corners edges if needed. Make sure all mating surfaces are clean and free of excess dust & debris. Using 4” brush or a spray bottle, thoroughly moisten all bond surfaces.

THIS MUST BE DONE TO ENSURE PROPER ADHESION OF COMPONENTS AND SEALING OF JOINTS IF ANY PARTS ARE DAMAGED DO NOT INSTALL CONTACT DEALER FOR REPLACEMENT

FIREBOX

A. BASE PEDESTAL PREPARATION

 

 

VFT

Make sure floor is level

 

 

 

 

 

 

 

B. . CENTER SECTION INSTALLATION (2 PARTS)

 

 

 

 

 

 

 

The center back wall consists of 2 sections assembled against each other.

 

 

 

 

 

 

 

DO NOT BOND FRONT & REAR SECTIONS TO EACH OTHER.

 

 

 

 

 

 

 

Apply a 3” wide X ¼” thick bed of refractory adhesive to base approximately 1”

 

 

 

 

 

 

CR

 

 

C-2 Parts

in from edges of sides and back. (Where sides and back will sit.) Stand both

 

 

 

 

sections of back wall on base and support while applying adhesive to cover the

 

 

 

 

 

 

 

CL

 

 

 

 

 

 

join line between front & rear sections. The coating of cement should cover the

 

 

 

 

 

 

seam all around the outer edges of the back wall. This coat should be smooth

 

 

 

 

 

 

 

but not excessive. (1/8” thick max.)

 

 

 

B

 

 

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents For Your Safety What to do if YOU Smell GASSave this Book ListedDo not Install this Unvented Assembly in Sleeping Quarters Selecting LocationIntroduction Before YOU BeginPreparation for Firebox Assembly Do not Install this Unvented Assembly in Sleeping QuartersFraming Dimensions FramingClearances Part PreparationFirebox GAS Supply Testing TOP Section InstallationMantle Clearances 11 ½Finishing the Fireplace Fireplace FacingOperating Guidelines and Maintenance Instructions Replacement and Accessory PartsLogs can GET Very HOT!! Handle only When Cool Before OrderingFirebox

36, 42, 48 specifications

Southwest Specialty Products 48, 36, and 42 are innovative solutions designed to meet the diverse needs of various industries, including construction, manufacturing, and environmental management. These products showcase advanced technologies and practical features aimed at enhancing efficiency, safety, and performance in demanding environments.

One of the standout features of the 48, 36, and 42 models is their robust construction. Made from high-grade materials, these products offer exceptional durability, ensuring long-lasting performance even under the toughest conditions. They are resistant to corrosion, which is crucial for applications in harsh environments, thus reducing maintenance costs and increasing operational lifespan.

The 48, 36, and 42 models also incorporate cutting-edge technology to optimize functionality. For instance, they are equipped with advanced chemical compatibility, enabling users to safely use a wide range of substances without fear of degradation. This characteristic is particularly beneficial for industries that handle hazardous materials, as it promotes safety and allows for more versatile applications.

Another key technological advancement is the incorporation of user-friendly designs. These models feature ergonomic handles and intuitive controls, making them easy to operate. This is crucial in environments where time efficiency is essential, as users can quickly adapt and utilize the equipment without extensive training.

In terms of size and capacity, the 48, 36, and 42 models cater to various requirements, allowing customization based on specific project needs. This flexibility makes them an excellent choice for contractors, engineers, and facility managers who require reliable and scalable solutions.

Furthermore, environmental considerations are integral to the design of Southwest Specialty Products. The 48, 36, and 42 models are engineered with eco-friendly practices in mind, promoting sustainability while maintaining high performance levels. This commitment to the environment is increasingly important in today's market, where businesses are held accountable for their environmental footprint.

In conclusion, Southwest Specialty Products 48, 36, and 42 stand out due to their robust construction, advanced technology, user-friendly designs, and environmental consciousness. These features make them ideal choices for professionals seeking reliable, efficient, and safe solutions in various high-demand industries.
Top Page Image Contents