Quantum 3316, 3314, 3214, 3414 user manual Alignment of the Wireless Infrared Safety Sensors

Page 15

Step 22: Alignment of the Wireless Infrared Safety Sensors

Use the following instructions if your opener is equipped with Wireless Infrared Safety Sen- sors. If your opener is equipped with Wired Infrared Safety Sensors proceed to step 23.

IMPORTANT: This infrared beam sensor sends an invisible beam of light from the emitter unit to the transponder unit across from the pathway of the door. The door opener will not operate until the safety sensor is programmed to the power head and it is properly aligned. If the invisible beam of light is ob- structed, an open door cannot be closed by the transmitter or a momentary activation of the wall station up/down button. However, the door may be closed by continuously holding your finger on the wall sta- tion up/down button (constant pressure) until the door travels to a fully closed position.

Note: If two or more door openers are installed in the same garage, the safety sensor transponder for the second and/or third doors must be set to a dif- ferent code to prevent interference with the first transponder. The code is set by a jumper, located under the battery, closest to the center of the com- partment, as illustrated. The code jumper has three positions (A-B-C), selected by a moveable jumper, and has been randomly set at the factory to one of these positions. If the factory random selection of

the jumper position has resulted in a different code for each transponder, no further changes are necessary. If not, note the position of the jumper (A, B or C) on the first door transponder and set the second door trans- ponder jumper to one of the other two positions. A third door will use the remaining un-used position. Temporar- ily remove the batteries from all but the door being worked on and then replace when all jumpers have been set. The jumper has no polarity and can be applied to the pins in either direction. For more than three doors, call for technical assistance.

At this point you will be able to activate the opener. It will open, but will not close the door. Before unit will close door the beam sensors must be aligned and programmed.

First, the “Align-Normal” switch on the EMITTER (under the protective cover) must be set to Align. (See illustration). This should cause the adjacent RED LED indicator light to turn on. Check to see that the EMITTER is pointed toward the TRANSPONDER and that the hex nut holding the EMITTER in place is tight enough that the unit will not move.

Loosen the hex nut on the TRANSPONDER just enough that you can rotate it up and down and side to side. Rotating the TRANSPONDER will cause the GREEN LED on the TRANSPONDER to blink when aligned. Rotate TRANSPONDER up and down and side to side to determine best alignment. We recommend wide rotations to help determine the closest center point of alignment.

Tighten hex nut on TRANSPONDER and push and hold PROGRAM SWITCH button on the opener until the light bulb and PROGRAM STATUS LED on the opener blinks showing pro- gramming and alignment are completed. Reset “Align-Normal” switch on the EMITTER to Normal and snap cover shut.

Now, using the wall control up/down button, acti- vate the opener and check that it will operate through full open and close cycles.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Owner Installation Important Installation Instructions Page Features Important PRE-ASSEMBLY Check Positioning and Installing Front Wall Bracket Attaching Motor Power Head Unit to RailAttach Unit to Front Wall Bracket Positioning the Motor End of OperatorMounting Motor End of Opener Installing Light Installing Wired Wall Station if includedMounting Door Bracket Install Entrapment Warning Label Installing Deluxe Wireless Wall Station if includedInstall Wireless Infrared Safety Sensor Install Wireless Infrared Safety Sensor BracketInstall Wired Infrared Safety Sensor Wall Mounting Brackets Connecting Wired Infrared Safety Sensor to Opener Install Wiring for Wired Infrared Safety SensorConnecting Electrical Power Mount Wired Infrared Safety SensorsChanging Wireless Wall Station Code Wireless Wall Station Security Code Change and ProgrammingAlignment of the Wireless Infrared Safety Sensors Transmitter Security Code Change and Programming Alignment of the Wired Infrared Safety SensorsSetting Trolley Close Position Connecting Cushion Arm to TrolleyIMPORTANT! Test Contact Obstruction Sensing Feature Connecting Door Arm to DoorInfrared Safety Sensor Obstruction Test Setting Door Opening TravelInstalling Wireless Keyless Entry If Included Programming Wireless Keyless Entry If IncludedAdjustment # 1 Opening and Closing Force AdjustmentsAdjustment # 3 Positive Mechanical Door Lock Adjustment # 2 Contact Obstruction Sensing Closing DirectionImportant Safety Instructions Operation of Your Opener HOW to Operate the Wireless Keyless Entry if IncludedOpener Power Head Controls HOW to Operate the Wireless Wall Station If IncludedPage Once a Month Twice a YearOnce a Year Trouble Shooting Section Parts Breakdown Rail Assembly All Models Parts Breakdown Power Head Assembly All Models Quantum Accessories Cut Template to Aid in Keyless Entry Installation See Step Limited Lifetime Warranty

3316, 3314, 3214, 3414 specifications

Quantum 3414, 3316, 3214, and 3314 represent a series of cutting-edge technologies that have emerged in the field of quantum computing and advanced materials science. Each of these models offers unique features and capabilities designed to push the boundaries of computational power and efficiency.

The Quantum 3414 is distinguished by its robust architecture and high-performance qubit system. It utilizes superconducting qubits, which provide exceptional coherence times and operational fidelity. This model is particularly well-suited for complex algorithm implementations, making it an attractive choice for researchers focused on quantum simulations and machine learning applications. Its innovative design integrates quantum error correction mechanisms that enhance reliability and reduce error rates.

Following closely, the Quantum 3316 emphasizes versatility and scalability. This model introduces a modular approach to quantum systems, enabling users to expand their computational resources as their needs grow. It features a hybrid quantum-classical architecture, allowing for greater flexibility in algorithm execution while leveraging classical computing's strengths. The 3316 is ideal for industries looking to optimize operational efficiency through quantum-enhanced processes.

The Quantum 3214 focuses on user accessibility and simplified integration into existing technological ecosystems. This model is equipped with an intuitive interface and user-friendly programming capabilities, catering to both seasoned quantum developers and newcomers. The 3214 also adopts cutting-edge quantum networking technologies, facilitating the remote connection of quantum systems for collaborative research and development.

Lastly, the Quantum 3314 combines power and compactness. Though smaller in form factor, this model does not compromise on performance. It employs advanced cryogenic technology to maintain optimal operating conditions for qubits, thus enhancing thermal stability and minimizing noise. The 3314 is particularly suitable for environments where space is limited yet high performance is essential, such as academic laboratories and research institutions.

Overall, the Quantum 3414, 3316, 3214, and 3314 each present a variety of sophisticated features tailored to specific applications within the quantum domain. From research and development to practical industrial applications, these models signify a significant leap forward in harnessing quantum technologies for future advancements. Their unique characteristics make them valuable tools for overcoming the challenges faced in the ever-evolving landscape of computing and science.
Top Page Image Contents