Pella V983492 installation instructions 8FLUSH Flange Opening Prepartation

Page 12

8FLUSH FLANGE OPENING PREPARTATION (CONTINUED)

H. Install the wood blocking in the head existing door frame. Place a 3/16" bead of sealant in the door panel cavities, then insert the wood blocking into the head cavities. Next insert the wood blocking into the jamb panel cavities of the existing door frame.

I.Construct a door sill pan for the door. Measure the distance between the cut ends of the existing door sill and add 2". Measure 1" from each end and cut through the vertical leg of the pan material. Bend bottom flaps of the pan material up, then bend the back leg around the end of the pan.

CONSTRUCT A DOOR SILL PAN

 

1“

 

Cut

Fold

 

up

Fold

here

end

in tab

REPEAT STEPS FOR OPPOSITE END

TWO OR MORE PERSONS ARE REQUIRED fOR ThE fOLLOWINg STEPS.

J.Remove the packaging from the door. Inspect the frame and panels for damage. DO NOT install damaged units.

Note: If screens or hardware are removed from the door at this time, label them and store them in a protected area.

K.Remove the panel(s). With the jamb side of the door down, slide each panel all the way to the right or left, while lifting the panel out to the bottom frame pocket, swing the panel out of the frame.

Note: Door may have fixed panel fully installed. If so, remove the vent panel only.

L.Dry fit the sill pan and the door into the opening.

8K

2

1

Interior View

Note: If the new door frame is deeper than the existing door frame, it will be necessary to cut the interior flooring material back to allow the door flush flanges to contact the existing aluminum door frame.

M.from the exterior, set the door into the opening. Set the sill of the door on the sill pan and tilt the door into position.

N.Insert shims around the door temporarily while you verify that the door will fit into the opening and that the door flanges will overlap the stucco or existing aluminum door frame by a minimum of 3/4" on all sides.

Note: Fix any problems with the opening before proceeding.

Page-12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Table Of Contents Remember to USE Appropriate Personal Protective Equipment 1ROUGH Opening Preparation Interior2PREPARE the Door for Installation 3SETTING and Fastening the DoorLocate the kitted parts bag. Remove from unit Interior Jamb All frame Types4REINSTALL the Sliding Panel Install jamb pocket cover in pocket above bumper5INTEGRATING the Door to the Water Resistive Barrier 6INTERIOR SealApply the top flashing tape. Cut a Apply flashing tape to the diagonal cuts. Cut piecesWood Siding Shape, tool and clean excess sealant. When 7SEALING the Door to the Exterior Wall CladdingFLUSh fLANgE fRAME 8FLUSH Flange Opening Preparatation 8FLUSH Flange Opening Prepartation Dry fit the sill pan and the door into the opening9SETTING and Fastening the Door in Flush Flange Applications Applications Drive a #10 x 4 pan head corrosionInstallation Plumb and square the door. Insert shimsDrive a #10 pan head corrosion resistant screw CLEANINg Instructions Important Notice

V983492 specifications

The Pella V983492 is a highly regarded window series that brings together innovation, durability, and aesthetic appeal. Designed with energy efficiency in mind, it features a range of technologies that enhance both performance and comfort in any living space.

One of the standout attributes of the Pella V983492 is its energy-efficient design. Utilizing advanced Low-E insulating glass, this window significantly minimizes heat transfer during both hot and cold seasons. It helps keep interiors comfortable, reducing the reliance on heating and cooling systems, which can lead to significant energy savings over time. Additionally, the argon gas fill between the glass panes further increases insulation, thereby enhancing the overall efficiency.

Durability is another critical aspect of the Pella V983492. Constructed with a robust frame, this window is designed to withstand various weather conditions, ensuring long-lasting performance. Pella uses high-quality materials that resist rot, fading, and even impact damage, which are common challenges faced by windows over time. This commitment to durability means that homeowners can expect minimal maintenance and enduring beauty.

In terms of design, the Pella V983492 offers a variety of styles, sizes, and finishes, making it a versatile choice for diverse architectural aesthetics. Homeowners can choose from different grid patterns and colors to match the exterior of their home, ensuring that these windows not only function effectively but also enhance curb appeal. This customizability allows for a seamless integration with any home design, whether traditional or modern.

Another notable feature of the Pella V983492 is its ease of use. With features such as simple operating mechanisms, these windows provide homeowners with a seamless experience when opening and closing. The addition of advanced locking mechanisms ensures enhanced security, providing peace of mind for residents.

Overall, the Pella V983492 serves as an exemplary choice for those looking to invest in high-quality, energy-efficient windows. With its combination of advanced technologies, durable construction, and aesthetic flexibility, it addresses the needs of modern homeowners who prioritize both functionality and style in their living spaces.
Top Page Image Contents