Pella V983492 installation instructions Interior

Page 5

3SETTING AND FASTENING THE DOOR (CONTINUED)

B.Dry fit the door. Make sure the door is plumb, square and level. Drill anchor locations with 1/8" masonry bit. Mark the interior of the door frame at the sill to show a boundary for sealant placement. Carefully remove and set the door aside.

C.Apply two continuous 1/4" to 3/8" diameter beads of sealant across the sill of the opening and 12" up the jambs, towards the interior side of the door (between the anchor holes and interior edge of door). DO NOT apply sealant between the anchor holes and the exterior side of the sill plate or floor.

Note: Failure to properly seal the sill attachment screws and sill plate may allow water to penetrate the interior of the home.

3C

anchor hole

12"

Interior View

D.Insert the door from the exterior of the building. Place the bottom of the door at the bottom of the opening, then tilt the top into position. Center the door between the sides to allow equal clearance for shimming. Make sure the door is plumb, level and square.

Door frames with Nail fin: Insert one 2" galvanized roofing nail into the top of each jamb nailing fin.

Door frames without Nail fin: Insert one screw in the top hole of each jamb.

Note: When installing doors without a bottom fin, DO NOT slide the bottom of the door into the opening, as sliding will damage the sealant lines. Insert sill anchor screws prior to shimming.

Exterior

3D

E.Plumb and square the door. Insert shims at the jambs between the door and the sides of the rough opening. Place shims behind each of the pre-drilled installation holes. DO NOT place shims at the sill. DO NOT place shims at the head until Step 4I.

Interior

3E

Page-5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Table Of Contents Remember to USE Appropriate Personal Protective Equipment Interior 1ROUGH Opening PreparationLocate the kitted parts bag. Remove from unit 2PREPARE the Door for Installation3SETTING and Fastening the Door Interior All frame Types JambInstall jamb pocket cover in pocket above bumper 4REINSTALL the Sliding Panel6INTERIOR Seal 5INTEGRATING the Door to the Water Resistive BarrierApply the top flashing tape. Cut a Apply flashing tape to the diagonal cuts. Cut piecesWood Siding FLUSh fLANgE fRAME Shape, tool and clean excess sealant. When7SEALING the Door to the Exterior Wall Cladding 8FLUSH Flange Opening Preparatation Dry fit the sill pan and the door into the opening 8FLUSH Flange Opening Prepartation9SETTING and Fastening the Door in Flush Flange Applications Drive a #10 x 4 pan head corrosion ApplicationsDrive a #10 pan head corrosion resistant screw InstallationPlumb and square the door. Insert shims Important Notice CLEANINg Instructions

V983492 specifications

The Pella V983492 is a highly regarded window series that brings together innovation, durability, and aesthetic appeal. Designed with energy efficiency in mind, it features a range of technologies that enhance both performance and comfort in any living space.

One of the standout attributes of the Pella V983492 is its energy-efficient design. Utilizing advanced Low-E insulating glass, this window significantly minimizes heat transfer during both hot and cold seasons. It helps keep interiors comfortable, reducing the reliance on heating and cooling systems, which can lead to significant energy savings over time. Additionally, the argon gas fill between the glass panes further increases insulation, thereby enhancing the overall efficiency.

Durability is another critical aspect of the Pella V983492. Constructed with a robust frame, this window is designed to withstand various weather conditions, ensuring long-lasting performance. Pella uses high-quality materials that resist rot, fading, and even impact damage, which are common challenges faced by windows over time. This commitment to durability means that homeowners can expect minimal maintenance and enduring beauty.

In terms of design, the Pella V983492 offers a variety of styles, sizes, and finishes, making it a versatile choice for diverse architectural aesthetics. Homeowners can choose from different grid patterns and colors to match the exterior of their home, ensuring that these windows not only function effectively but also enhance curb appeal. This customizability allows for a seamless integration with any home design, whether traditional or modern.

Another notable feature of the Pella V983492 is its ease of use. With features such as simple operating mechanisms, these windows provide homeowners with a seamless experience when opening and closing. The addition of advanced locking mechanisms ensures enhanced security, providing peace of mind for residents.

Overall, the Pella V983492 serves as an exemplary choice for those looking to invest in high-quality, energy-efficient windows. With its combination of advanced technologies, durable construction, and aesthetic flexibility, it addresses the needs of modern homeowners who prioritize both functionality and style in their living spaces.
Top Page Image Contents