Pella V983492 installation instructions Jamb, All frame Types

Page 6

3SETTING AND FASTENING THE DOOR (CONTINUED)

F. fasten the door to the opening:

 

Door frames with Nail fin Only: Insert one 2" galvanized

 

roofing nail into every other pre-punched hole in the nailing fin.

 

All frame Types:

 

Transom/Sidelight: Remove the sill track and pocket covers

 

by pulling on the paper ring.

 

head and Jambs: At each pre-drilled installation hole, drill

 

1/8" pilot holes through the outer frame wall, shims and the

 

rough opening. Drive #10 x 2" corrosion resistant pan head

 

screws (wood rough openings) or 1/4" x 2" masonry screws

 

JAMB

(masonry rough openings) into each pre-drilled hole.

Sill: Place a dab of sealant in each pre-drilled hole in the sill

 

prior to installing the sill screws. Place a #10 rubber washer

 

on each sill screw. Drive the screw until the head contacts the

 

frame, however DO NOT sink the head.

 

Note: At the sill, it is imperative that sealant be applied under the screw heads and that it surrounds them to prevent water leakage. Failure to properly seal the sill attachment screws may allow water to penetrate the interior of the home.

Sidelights and Transoms Only: Replace the pocket covers and sill track.

G. Secure the fixed panel(s) by driving in the #10 x 1-1/2" fixed panel screws. Install the screws from the interior at an angle as shown. Space one screw 16" from the top and one 16" from the bottom then one screw in the center.

EXTERIOR

3G

INTERIOR

Fixed Side - Exterior Frame Pocket

H.Install the panel track. Clean the pocket of any debris and snap the track into the interior panel pocket.

 

3H

Exterior

Interior

I.Install the panel bumpers. Locate the slit on the bumper(s) and place it on the track. Press down to seat the bumper onto the panel track cap.

3I

Page-6

Image 6
Contents Table Of Contents Remember to USE Appropriate Personal Protective Equipment 1ROUGH Opening Preparation Interior2PREPARE the Door for Installation 3SETTING and Fastening the DoorLocate the kitted parts bag. Remove from unit Interior Jamb All frame Types4REINSTALL the Sliding Panel Install jamb pocket cover in pocket above bumperApply the top flashing tape. Cut a 5INTEGRATING the Door to the Water Resistive Barrier6INTERIOR Seal Apply flashing tape to the diagonal cuts. Cut piecesWood Siding Shape, tool and clean excess sealant. When 7SEALING the Door to the Exterior Wall CladdingFLUSh fLANgE fRAME 8FLUSH Flange Opening Preparatation 8FLUSH Flange Opening Prepartation Dry fit the sill pan and the door into the opening9SETTING and Fastening the Door in Flush Flange Applications Applications Drive a #10 x 4 pan head corrosionInstallation Plumb and square the door. Insert shimsDrive a #10 pan head corrosion resistant screw CLEANINg Instructions Important Notice

V983492 specifications

The Pella V983492 is a highly regarded window series that brings together innovation, durability, and aesthetic appeal. Designed with energy efficiency in mind, it features a range of technologies that enhance both performance and comfort in any living space.

One of the standout attributes of the Pella V983492 is its energy-efficient design. Utilizing advanced Low-E insulating glass, this window significantly minimizes heat transfer during both hot and cold seasons. It helps keep interiors comfortable, reducing the reliance on heating and cooling systems, which can lead to significant energy savings over time. Additionally, the argon gas fill between the glass panes further increases insulation, thereby enhancing the overall efficiency.

Durability is another critical aspect of the Pella V983492. Constructed with a robust frame, this window is designed to withstand various weather conditions, ensuring long-lasting performance. Pella uses high-quality materials that resist rot, fading, and even impact damage, which are common challenges faced by windows over time. This commitment to durability means that homeowners can expect minimal maintenance and enduring beauty.

In terms of design, the Pella V983492 offers a variety of styles, sizes, and finishes, making it a versatile choice for diverse architectural aesthetics. Homeowners can choose from different grid patterns and colors to match the exterior of their home, ensuring that these windows not only function effectively but also enhance curb appeal. This customizability allows for a seamless integration with any home design, whether traditional or modern.

Another notable feature of the Pella V983492 is its ease of use. With features such as simple operating mechanisms, these windows provide homeowners with a seamless experience when opening and closing. The addition of advanced locking mechanisms ensures enhanced security, providing peace of mind for residents.

Overall, the Pella V983492 serves as an exemplary choice for those looking to invest in high-quality, energy-efficient windows. With its combination of advanced technologies, durable construction, and aesthetic flexibility, it addresses the needs of modern homeowners who prioritize both functionality and style in their living spaces.