Pella V983492 installation instructions Installation, Plumb and square the door. Insert shims

Page 15

9SETTINg AND fASTENINg ThE DOOR IN fLUSh fLANgE

APPLICATIONS (CONTINUED)

G.Plumb and square the door. Insert shims

between the new door frame and the existing door

 

frame at the pre-drilled anchor hole locations in

 

the door jambs. DO NOT ShIM ThE hEAD UNTIL

 

ALL fIXED PANELS ARE INSTALLED. Move the

 

door in the opening until the flanges are tight

9G

against the existing aluminum door frame.

 

Note: DO NOT over shim.

H. Drill a 1/8" pilot hole through the door frame, shims, blocking and aluminum frame at each pre- drilled installation screw hole location.

I.Drive a #10 pan head corrosion resistant screw

into the rough opening at the installation hole locations.

DO NOT INSTALL fASTENERS IN hEAD UNTIL ALL fIXED PANELS hAVE BEEN INSTALLED.

go to Step 4

10 OPTIONAL SILL PAN fABRICATION

AND INSTALLATION

Construct a door sill pan for the door. Measure the distance between the cut ends of the existing door sill and add 2". Measure 1" from each end and cut through the vertical leg of the pan material. Bend bottom flaps of the pan material up, then bend the back leg around the end of the pan.

Dry fit the sill pan and the door into the opening.

CONSTRUCT A DOOR SILL PAN

 

1“

 

Cut

Fold

 

up

Fold

here

end

in tab

REPEAT STEPS FOR OPPOSITE END

from the exterior, set the door into the opening. Set the sill of the door on the sill panel and tilt the door into position.

Using a pencil, mark the interior and exterior edges of the sill pan on the sill of the rough opening. Remove the door and sill pan.

Place a 1/4” diameter bead of sealant in the following locations:

-The exterior side of the interior pencil mark.

-The interior side of the exterior pencil mark.

-Midway between the exterior and interior sealant beads.

Page-15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Table Of Contents Remember to USE Appropriate Personal Protective Equipment Interior 1ROUGH Opening Preparation2PREPARE the Door for Installation 3SETTING and Fastening the DoorLocate the kitted parts bag. Remove from unit Interior All frame Types JambInstall jamb pocket cover in pocket above bumper 4REINSTALL the Sliding PanelApply flashing tape to the diagonal cuts. Cut pieces 5INTEGRATING the Door to the Water Resistive Barrier6INTERIOR Seal Apply the top flashing tape. Cut aWood Siding Shape, tool and clean excess sealant. When 7SEALING the Door to the Exterior Wall CladdingFLUSh fLANgE fRAME 8FLUSH Flange Opening Preparatation Dry fit the sill pan and the door into the opening 8FLUSH Flange Opening Prepartation9SETTING and Fastening the Door in Flush Flange Applications Drive a #10 x 4 pan head corrosion ApplicationsInstallation Plumb and square the door. Insert shimsDrive a #10 pan head corrosion resistant screw Important Notice CLEANINg Instructions

V983492 specifications

The Pella V983492 is a highly regarded window series that brings together innovation, durability, and aesthetic appeal. Designed with energy efficiency in mind, it features a range of technologies that enhance both performance and comfort in any living space.

One of the standout attributes of the Pella V983492 is its energy-efficient design. Utilizing advanced Low-E insulating glass, this window significantly minimizes heat transfer during both hot and cold seasons. It helps keep interiors comfortable, reducing the reliance on heating and cooling systems, which can lead to significant energy savings over time. Additionally, the argon gas fill between the glass panes further increases insulation, thereby enhancing the overall efficiency.

Durability is another critical aspect of the Pella V983492. Constructed with a robust frame, this window is designed to withstand various weather conditions, ensuring long-lasting performance. Pella uses high-quality materials that resist rot, fading, and even impact damage, which are common challenges faced by windows over time. This commitment to durability means that homeowners can expect minimal maintenance and enduring beauty.

In terms of design, the Pella V983492 offers a variety of styles, sizes, and finishes, making it a versatile choice for diverse architectural aesthetics. Homeowners can choose from different grid patterns and colors to match the exterior of their home, ensuring that these windows not only function effectively but also enhance curb appeal. This customizability allows for a seamless integration with any home design, whether traditional or modern.

Another notable feature of the Pella V983492 is its ease of use. With features such as simple operating mechanisms, these windows provide homeowners with a seamless experience when opening and closing. The addition of advanced locking mechanisms ensures enhanced security, providing peace of mind for residents.

Overall, the Pella V983492 serves as an exemplary choice for those looking to invest in high-quality, energy-efficient windows. With its combination of advanced technologies, durable construction, and aesthetic flexibility, it addresses the needs of modern homeowners who prioritize both functionality and style in their living spaces.
Top Page Image Contents