Pella 803V0102 installation instructions Prepare the Door for Installation

Page 3

1ROUGH OPENING PREPARATION (CONTINUED)

D.Fold the water resistive barrier. Fold side flaps into the opening and staple to the inside wall. Fold the top flap up and temporarily fasten with flashing tape.

E.Apply sill flashing tape #1. Cut a piece of flashing tape 12" longer than the opening width. Apply at the bottom of the opening as shown so it overhangs 1" to the exterior.

Note: The tape is cut 12" longer than the width of the opening so it will extend up each side approximately 6".

Exterior

1D

F.Tab the sill flashing tape and fold. Cut 1" wide tabs at each corner (1/2" from each side of corner). Fold tape to the exterior and press firmly to adhere it to the water resistive barrier.

G.Apply sill flashing tape #2. Cut a piece of flashing tape 12" longer than the opening width. Apply at the bottom, overlapping tape #1 by at least 1". DO NOT allow the tape to extend past the interior face of the frame.



1E&







1E'

Note: The flashing tape does not need to extend all the way to the interior of the framing.

H.Attach the aluminum sill support or wood blocking to the exterior of the sill structure to support the edge of the door sill. The sill support should be cut the entire length of the sill member and placed flush with the subfloor.



1G(

1H

)

2PREPARE THE DOOR FOR INSTALLATION

A.Remove the plastic wrap and cardboard packaging from the door.

Note: If screens or hardware are removed from the door at this time, label them and store them in a protected area.

B.OX/XO doors only: Remove the shipping spacers. Carefully slide the movable panel halfway open and remove the spacers from both the top and bottom of the movable panel.

TWO OR MORE PEOPLE WILL BE REQUIRED

TO HANDLE THE PANEL AND FRAME SAFELY.

C.OX/XO doors only: If the vent panel is installed in the frame, you will need to remove the vent panel by lifting it out of the lower track and tilting the bottom of the panel away from the door frame. Then lower the panel out of the top track. Carefully set the panel aside.

Note: If transoms or fixed units are mulled to doors and/or fins are to be installed to no fin units, go to the Mulling Instructions and/or Applying Installation Fins Instructions on the back before proceeding to the next step.

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Remember to USE Appropriate Personal Protective Equipment For complete details on http//warranty.pellaimpervia.comCut the water resistive barrier Rough Opening PreparationPrepare the Door for Installation Do not slide the bottom of the door into Setting and Fastening the DoorTWO or More People will be Required for Following Steps Insert the door from the exterior of the buildingIntegrating the Door to the Water Resistive Barrier Entire nailing fin, but not Extend onto the door frame.flashing tape to prevent water from getting behind it Reinstall the Vent Panel OX/XO Doors only Interior SealApply insulating foam sealant. From the interior, insert Sealant line Sealing the Door to the Exterior Wall CladdingWidth of the transom frame Foot Bolt AdjustmentMulling Instruction Horizontal MullionsVertical Mullions Notch the ends of the fins. Measure Applying Installation FinsCut the fins to length. Using the following When applying fins to mulled products, place a lineFinish Care and Maintenance Important NoticeThis page left blank intentionally

803V0102 specifications

The Pella 803V0102 is an advanced window solution that combines modern design with cutting-edge technology, making it an ideal choice for homeowners seeking both aesthetics and performance. Known for its energy efficiency, the Pella 803V0102 features triple-pane glass that significantly reduces heat transfer, ensuring that homes remain comfortable regardless of the season. This multi-layered glass structure helps to keep indoor heating and cooling efforts efficient, thereby reducing energy bills over time.

One of the standout characteristics of the Pella 803V0102 is its innovative Low-E glass coating. This specialized coating reflects infrared light while allowing visible light to pass through, maximizing natural light while minimizing heat loss. The innovative design also contributes to the window's ability to reduce harmful UV rays, protecting furniture and flooring from fading, which is often a concern in sun-drenched areas.

In terms of durability, the Pella 803V0102 is engineered with robust frames crafted from high-quality materials. The frame construction is designed to withstand weather extremes, ensuring longevity and stability. Additionally, the window is equipped with a water-repellent exterior finish, which protects against moisture damage while requiring minimal maintenance over the years.

The Pella 803V0102 also boasts noise-reduction technologies, making it an excellent choice for homes in busy urban environments. The combination of multiple glass panes and specialized seals effectively dampens outside noises, creating a tranquil indoor atmosphere.

Security is another priority for the Pella 803V0102. The window is fitted with advanced locking mechanisms, which offer enhanced protection against break-ins, providing peace of mind for homeowners. Furthermore, the design of the window can accommodate various styles, making it suitable for different architectural preferences from traditional to contemporary homes.

Easy installation and customization options further enhance the appeal of the Pella 803V0102. Homeowners can choose from a variety of finishes, colors, and grille patterns to match their home’s style seamlessly.

In summary, the Pella 803V0102 represents a perfect blend of innovation, efficiency, and style. Its energy-saving features, acoustic performance, durability, and security technologies make it a leading choice for those looking to invest in high-quality windows that enhance both comfort and safety in their homes. Whether upgrading an existing home or building a new one, the Pella 803V0102 is poised to deliver exceptional value and performance.
Top Page Image Contents