Pella 803V0102 Foot Bolt Adjustment, Mulling Instruction, Horizontal Mullions

Page 8

8FOOT BOLT ADJUSTMENT

A. Align foot bolt to the strike, then tighten the

8A

exposed screw.

B. Slide the foot bolt actuator to the opposite position and tighten the screw.

C.Check the door and foot blot for proper operation. If the foot bolt assembly location needs to be adjusted, loosen both attachment screws and adjust foot bolt location, re-tighten

the screws.

8B

8C

MULLING INSTRUCTION

HORIZONTAL MULLIONS:

Note: If transoms are to be attached (mulled) to the top of the unit, perform this process before attaching fins.

A.Apply two strips of foam tape across the bottom of the transom frame.

Note: The tape must extend the full

0QUJPOBM+BNC&YUFOTJPO

 

width of the transom frame.

5SBOTPN6OJU

 

B. Place a foam plug at each end of the top

A"

between the exterior rib and the joining

 

 

mullion groove.

C$

 

C. Position and align the transom with the

 

 

 

sliding door.

B#

D%

D. Start the I bar joining connector from

4MJEJOH%PPS

 

one end and drive it to the full width of the

 

 

units.

 

 

Note: A rubber mallet may be used to drive the I bar joining connector into position. If necessary, the I bar joining connector can be cut in half and driven from each end.

E.Apply sealant to the ends of the mullion joint. The bead of sealant should extend from the center of the mullion joint to the exterior of the unit, covering the foam plug.

Page 7 Page 9
Image 8
Page 7 Page 9
Contents For complete details on http//warranty.pellaimpervia.com Remember to USE Appropriate Personal Protective EquipmentRough Opening Preparation Cut the water resistive barrierPrepare the Door for Installation Setting and Fastening the Door TWO or More People will be Required for Following StepsInsert the door from the exterior of the building Do not slide the bottom of the door intoflashing tape to prevent water from getting behind it Integrating the Door to the Water Resistive BarrierEntire nailing fin, but not Extend onto the door frame. Apply insulating foam sealant. From the interior, insert Reinstall the Vent Panel OX/XO Doors onlyInterior Seal Sealing the Door to the Exterior Wall Cladding Sealant lineFoot Bolt Adjustment Mulling InstructionHorizontal Mullions Width of the transom frameVertical Mullions Applying Installation Fins Cut the fins to length. Using the followingWhen applying fins to mulled products, place a line Notch the ends of the fins. MeasureCare and Maintenance Important Notice FinishThis page left blank intentionally

803V0102 specifications

The Pella 803V0102 is an advanced window solution that combines modern design with cutting-edge technology, making it an ideal choice for homeowners seeking both aesthetics and performance. Known for its energy efficiency, the Pella 803V0102 features triple-pane glass that significantly reduces heat transfer, ensuring that homes remain comfortable regardless of the season. This multi-layered glass structure helps to keep indoor heating and cooling efforts efficient, thereby reducing energy bills over time.

One of the standout characteristics of the Pella 803V0102 is its innovative Low-E glass coating. This specialized coating reflects infrared light while allowing visible light to pass through, maximizing natural light while minimizing heat loss. The innovative design also contributes to the window's ability to reduce harmful UV rays, protecting furniture and flooring from fading, which is often a concern in sun-drenched areas.

In terms of durability, the Pella 803V0102 is engineered with robust frames crafted from high-quality materials. The frame construction is designed to withstand weather extremes, ensuring longevity and stability. Additionally, the window is equipped with a water-repellent exterior finish, which protects against moisture damage while requiring minimal maintenance over the years.

The Pella 803V0102 also boasts noise-reduction technologies, making it an excellent choice for homes in busy urban environments. The combination of multiple glass panes and specialized seals effectively dampens outside noises, creating a tranquil indoor atmosphere.

Security is another priority for the Pella 803V0102. The window is fitted with advanced locking mechanisms, which offer enhanced protection against break-ins, providing peace of mind for homeowners. Furthermore, the design of the window can accommodate various styles, making it suitable for different architectural preferences from traditional to contemporary homes.

Easy installation and customization options further enhance the appeal of the Pella 803V0102. Homeowners can choose from a variety of finishes, colors, and grille patterns to match their home’s style seamlessly.

In summary, the Pella 803V0102 represents a perfect blend of innovation, efficiency, and style. Its energy-saving features, acoustic performance, durability, and security technologies make it a leading choice for those looking to invest in high-quality windows that enhance both comfort and safety in their homes. Whether upgrading an existing home or building a new one, the Pella 803V0102 is poised to deliver exceptional value and performance.
Top Page Image Contents