Monte Carlo Fan Company 5HS42 Series Such as a tag, to the service panel, Canopy disk Downrod

Page 2

SAFETY TIPS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS

1.Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes ANSI/NFPA 70-1999),

2.including fire-rated construction.

3.Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding con-

4.ductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box.

Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device,

5.such as a tag, to the service panel.

6.Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

7.When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7

8.feet from the floor to the trailing edge of the blade.

To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system acceptable for fan support.

9.(Mounting must support at least 35 lbs.)

Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating

10.blades.

11.Attach the mounting bracket using only the hardware supplied with the outlet box.

12.To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.

13.If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

14.NEVER place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heat- ing equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA),

15.and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

TOOLS REQUIRED

Phillips Screwdriver Wire Cutters Pliers Step Ladder

1 2 3

 

Before you begin installing the fan, Switch

 

 

 

 

 

 

 

 

 

Use metal outlet box suitable for fan support

 

 

 

Before installing this fan make sure the outlet box is

 

 

(must support 35 lbs). Before attaching fan to

 

power off at Service panel and lock service dis-

 

 

 

 

outlet box, ensure the outlet box is securley fas-

 

properly installed to the house structure. To reduce

 

connecting means to prevent power from being

 

 

 

 

tened by at least two points to a structural ceil-

 

switched on accidentally. When the service dis-

 

 

the risk of fire, electric shock, or personal injury,

 

 

 

connecting means cannot be locked, securely

 

 

mount to outlet box or supporting system acceptable

 

 

ing member ( a loose box will cause the fan to

 

fasten a prominent warning device, such as a

 

 

for fan support. (Mounting must support at least 35

 

 

wabble). Use only the screws provided with

 

tag, to the service panel.

 

 

 

 

lbs.)

 

 

 

 

 

the outlet box.

 

4

 

Canopy disk

 

 

 

Downrod

 

 

 

5

 

 

 

 

 

 

6

 

 

 

 

 

 

 

 

 

 

 

Cross Pin

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Yoke

 

 

 

 

 

 

Canopy

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Keeper

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pin

 

 

 

 

 

 

Tread leadwires and

 

safety cable first

 

 

 

Insert downrod into yoke on

 

top of the Fan

 

 

Tighten the 2 Set screws on the Yoke

 

 

 

 

 

 

 

 

 

 

 

through the canopy disk, Canopy and

 

 

Body.

Align the hole in the Downrod with the

 

 

once the downrod is in place.

 

 

lastly downrod.

 

 

 

 

hole in the Yoke. Insert the Pin through the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Yoke and Downrod until the point appears on

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the other side. Install the Keeper Pin

 

 

 

 

 

Image 2
Contents OWNER’S Manual Canopy disk Downrod Such as a tag, to the service panelTread leadwires Safety cable first CanopyCenter Pass leadwires and safety cable through the canopyBlack Blue White Ground Hole Larger Smaller HolesPage Customer Service Center