Mega Catch Mini technical manual

Page 11
THROUGH WALL WITH VERTICAL RISE AND HORIZONTAL TERMINATION INSTALLATION - FREESTANDING:
A 45° elbow with a rodent screen may be used in place of the termination cap (or stainless steel termination hood).
Figure 12 is the recommended installation set up.
Figure 13 is the installation to use if there is a concrete or retaining wall in line with exhaust vent on a pellet stove. The termination must be 12” (30 cm) from the outside wall and 12” (30 cm) above the ground.
Figure 11: Venting to use with straight through wall Installation.
High Temperature RTV
Silicone Required
Fresh Air Intake Tube
45° Elbow with screen or
Termination Cap
Wall Thimble
3" (75mm) or 4" (100mm) "PL" or "L" vent
Exhaust Tube
with local building codes. 6. Install a length of 3” (75 mm)
or 4” (100 mm) vent pipe into the wall thimble. The pipe should install easily into the thimble.
7. Connect the exhaust vent pipe to the exhaust pipe on the stove. Seal the connection with high temperature silicone.
8. Push the stove straight back, leaving a minimum of 4” (10
cm) clearance from the back of the stove to the wall. Seal the vent pipe to the thimble with high temperature silicone.
9. The pipe must extend at least 12” (30 cm) away from the building. If necessary, bring
another length of pipe (PL type) to the outside of the home to connect to the first section. Do not forget to place high temperature silicone around the pipe that passes through the thimble.
10. Install a vertical pipe, or if all requirements for direct venting are met, install vent termination. The stainless steel cap termination manufactured by the vent manufacturer is recommended. However, when the vent terminates several feet above ground level and there are no trees, plants, etc. within several feet, a 45° elbow can be used as termination. The elbow must be turned down to prevent rain from entering.
NOTE:
• Some horizontal through wall installations may require a “T” and 3 to 5 feet (91 to 152 cm) of vertical pipe outside the building to help naturally draft in the unit.
• This may be required if a proper burn cannot be maintained, after the stove has been tested and the airflow set.
• This is due to the back pressure in the exhaust caused by airflow around the structure.
• All sections of pipe must have three (3) screws evenly spaced and all horizontal and vertical vent sections located within the house must have a bead of high temperature silicone installed on the male end of the pipe before installation to create a gas tight seal.
Installation

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Mini Table of Contents Introduction Introduction Screws to take out to remove stove from Pallet InstallationDimensions of Mini 91.5 cm Crawlspace, narrow Walkway Closely At center of unit Wiring, etc Page Venting horizontally with rise Refer to Figures 16 Freestanding hearth mount installation overview Exterior Blower Kit Through vent holeThrough Wall Installation with Exterior Blower Kit Sheathing To install the Optional slider damper rod, remove the left Special Notes Kit Components Installing the PanelsInstalling Hopper Lid Installing Hopper LidStove will not start TroubleshootingStove will not operate when hot Light # 2 on Heat output bar flashing 200 F 93 C high limit temperature sensor has trippedExhaust motor will not function normally Stove keeps going out Control settings Heat Level has no effect on the fireConvection blower will not function normally Ignitor- the pellets will not light5V DC Wiring DiagramReference Description Part Number Parts ListParts List Parts Diagram Components Parts Diagram Steel For the do-it-yourself Individual WarrantyName of Owner Address Installation Data Sheet

Mini specifications

The Mega Catch Mini is a state-of-the-art mosquito trap designed for users who demand effectiveness and ease of use in pest control. Compact in size yet powerful in performance, this innovative device is perfect for both indoor and outdoor settings, making it a versatile solution for homeowners and outdoor enthusiasts alike.

One of the main features of the Mega Catch Mini is its advanced CO2 technology. This trap imitates human breath by releasing carbon dioxide, which attracts mosquitoes and other flying insects. By mimicking the natural allure of humans, the Mega Catch Mini effectively increases its catch rate, ensuring fewer pesky insects buzzing around your space.

Another notable characteristic is its silent operation. Unlike traditional bug zappers that create an audible zap sound, the Mega Catch Mini operates quietly, ensuring that your peaceful evenings are undisturbed. This makes it an ideal choice for patio gatherings, backyard barbeques, or simply enjoying a quiet night at home.

The Mega Catch Mini is also equipped with a powerful fan that draws insects into a contained trap, preventing their escape. This efficient trapping mechanism eliminates the need for toxic chemicals or harmful pesticides, making it a safer option for households with children and pets.

Easy to set up and use, the Mega Catch Mini features a simple plug-and-play design. Users can easily place it in any location for optimal performance. Its lightweight design makes it easy to move from one area to another, ensuring that you can adapt to varying outdoor conditions.

In terms of maintenance, the Mega Catch Mini is user-friendly. It has a removable catching tray that can be easily cleaned and emptied. This simplicity in maintenance ensures that users can operate the unit consistently without the hassle of complicated procedures.

Power-efficient design is another hallmark of the Mega Catch Mini. It consumes minimal energy compared to traditional insect traps, reducing your electricity bills while keeping your space free from bugs.

Overall, the Mega Catch Mini stands out as an effective, user-friendly, and environmentally-friendly solution for controlling mosquito populations. Its innovative technology, combined with practical features, makes it a top choice for anyone looking to enjoy their outdoor spaces without the nuisance of insects.
Top Page Image Contents