Mega Catch Mini technical manual To install the Optional slider damper rod, remove the left

Page 18

Installation

THERMOSTAT INSTALLATION:

A) HI / LOW:

When the jumper is placed on only one of the J9 pins, then the control board is in a HI / LOW mode of thermostat operation (factory setting).

B) ON / OFF:

If both pins of J9 are jumped (covered), the control board is in an ON / OFF mode of thermostat operation.

Thermostat wires.

Figure 24: Circuit Board.

This control board can be placed into two different modes: When the jumper J9 is not jumped then the control board is in a HI / LOW mode operation. If the control board is placed with J9 jumped then the control board is in a ON / OFF mode of operation. In the ON /OFF thermostat mode, the unit will shut OFF when the thermostat is not calling for heat. When the thermostat calls for heat, the unit will go through an ignition sequence once again and relight.

1.Install the wall thermostat in a location that is not to close too the unit but will effectively heat the desired area.

2.Install a 12 or 24 Volt Thermostat using an 18 x 2 gauge wire from the unit to the thermostat.

If the unit has been placed in the HI / LOW mode, the unit will be taken to a low or idle setting when the thermostat is not calling for heat. When the thermostat calls for heat, the unit will go to the setting that is displayed on the control board Heat Indicator. If the heating load is not great enough when the stove is on low, the high limit switch will turn the stove off and the switch will have to be manually reset. To reset the high limit switch, remove the right cabinet side. The switch is found behind the control panel. Avoid setting off the high limit switch.

OPTIONAL SLIDER/DAMPER INSTALLATION:

 

If you wish to adjust the slider damper externally

 

(NOT REQUIRED), please follow the instructions

 

below.

 

Slider damper

 

 

rod and knob

 

 

7/16" Nut

 

Slider damper plate

7/16" Clinching Nut

 

Figure 25: Slider/Damper Assembly.

 

1. To install the OPTIONAL slider damper rod, remove the left

 

cabinet side and locate the slider damper plate. Install the 7/16

 

inch nut onto the slider damper rod, thread all the way to the

 

end of the threads on rod.

 

Slider/Damper

2. Slide rod through the hole in the slider damper plate and install

Knob

the 7/16” clinching nut onto the rod and tighten completely onto

 

 

 

the slider damper plate.

 

 

3. Re-install the cabinet side. Install the black knob on the end of

 

the rod. Check slider damper for smooth operation.

Figure 26: Slider/Damper Knob.

 

 

18

Image 18
Contents Mini Table of Contents Introduction Introduction Installation Screws to take out to remove stove from PalletDimensions of Mini 91.5 cm Crawlspace, narrow Walkway Closely At center of unit Wiring, etc Page Venting horizontally with rise Refer to Figures 16 Freestanding hearth mount installation overview Through vent hole Exterior Blower KitThrough Wall Installation with Exterior Blower Kit Sheathing To install the Optional slider damper rod, remove the left Special Notes Installing the Panels Kit ComponentsInstalling Hopper Lid Installing Hopper LidTroubleshooting Stove will not operate when hotStove will not start 200 F 93 C high limit temperature sensor has tripped Exhaust motor will not function normallyLight # 2 on Heat output bar flashing Ignitor- the pellets will not light Control settings Heat Level has no effect on the fireConvection blower will not function normally Stove keeps going outWiring Diagram 5V DCParts List Reference Description Part NumberParts List Parts Diagram Components Parts Diagram Steel Warranty For the do-it-yourself IndividualInstallation Data Sheet Name of Owner Address

Mini specifications

The Mega Catch Mini is a state-of-the-art mosquito trap designed for users who demand effectiveness and ease of use in pest control. Compact in size yet powerful in performance, this innovative device is perfect for both indoor and outdoor settings, making it a versatile solution for homeowners and outdoor enthusiasts alike.

One of the main features of the Mega Catch Mini is its advanced CO2 technology. This trap imitates human breath by releasing carbon dioxide, which attracts mosquitoes and other flying insects. By mimicking the natural allure of humans, the Mega Catch Mini effectively increases its catch rate, ensuring fewer pesky insects buzzing around your space.

Another notable characteristic is its silent operation. Unlike traditional bug zappers that create an audible zap sound, the Mega Catch Mini operates quietly, ensuring that your peaceful evenings are undisturbed. This makes it an ideal choice for patio gatherings, backyard barbeques, or simply enjoying a quiet night at home.

The Mega Catch Mini is also equipped with a powerful fan that draws insects into a contained trap, preventing their escape. This efficient trapping mechanism eliminates the need for toxic chemicals or harmful pesticides, making it a safer option for households with children and pets.

Easy to set up and use, the Mega Catch Mini features a simple plug-and-play design. Users can easily place it in any location for optimal performance. Its lightweight design makes it easy to move from one area to another, ensuring that you can adapt to varying outdoor conditions.

In terms of maintenance, the Mega Catch Mini is user-friendly. It has a removable catching tray that can be easily cleaned and emptied. This simplicity in maintenance ensures that users can operate the unit consistently without the hassle of complicated procedures.

Power-efficient design is another hallmark of the Mega Catch Mini. It consumes minimal energy compared to traditional insect traps, reducing your electricity bills while keeping your space free from bugs.

Overall, the Mega Catch Mini stands out as an effective, user-friendly, and environmentally-friendly solution for controlling mosquito populations. Its innovative technology, combined with practical features, makes it a top choice for anyone looking to enjoy their outdoor spaces without the nuisance of insects.