Mega Catch Mini technical manual Installation, Screws to take out to remove stove from Pallet

Page 5

Installation

DECIDING WHERE TO LOCATE YOUR PELLET APPLIANCE:

1. Check clearances to combustibles.

2. Do not obtain combustion air from an attic, garage or any unventilated space. Combustion air may be obtained from a ventilated crawlspace.

3. Do not install the stove in a bedroom.

4. You can vent the stove through an exterior wall behind the unit or connect it to an existing masonry or metal chimney (must be lined if the chimney is over 6” (15 cm) diameter, or over 28 inches² (180 cm²) cross sectional area). An interior vent can be used with approved pipe passing through the ceiling and roof.

5. Locate the stove in a large and open room that is centrally located in the house. This will optimize heat circulation.

6. The power cord is 8 feet (2.43 m) long and may require a grounded extension cord to reach the nearest electrical outlet.

REMOVING PELLET STOVE FROM PALLET:

 

1.

Remove the right and left hand cabinet sides by

 

loosening the three (3) T-20 Torx screws on the back

 

of the each panel.

2.

Remove the screw located on the front of the cabinet

 

side, below the louvers and loosen the screw behind

 

the ash door.

3.

Using a 5/16” socket of flat head screwdriver, remove

 

the three (3) wood screws that are holding the

 

bottom of the stove to the pallet. There is one (1)

 

screw behind each side panel and one (1) at the back

 

behind the back grill.

4.

Install the four (4) leveling legs into the nuts in the

 

base.

5.

Close the side panels.

Figure 1: Screws to take out to remove stove from

 

pallet.

 

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Mini Table of Contents Introduction Introduction Screws to take out to remove stove from Pallet InstallationDimensions of Mini 91.5 cm Crawlspace, narrow Walkway Closely At center of unit Wiring, etc Page Venting horizontally with rise Refer to Figures 16 Freestanding hearth mount installation overview Exterior Blower Kit Through vent holeThrough Wall Installation with Exterior Blower Kit Sheathing To install the Optional slider damper rod, remove the left Special Notes Kit Components Installing the PanelsInstalling Hopper Lid Installing Hopper LidStove will not start TroubleshootingStove will not operate when hot Light # 2 on Heat output bar flashing 200 F 93 C high limit temperature sensor has trippedExhaust motor will not function normally Convection blower will not function normally Control settings Heat Level has no effect on the fireIgnitor- the pellets will not light Stove keeps going out5V DC Wiring DiagramReference Description Part Number Parts ListParts List Parts Diagram Components Parts Diagram Steel For the do-it-yourself Individual WarrantyName of Owner Address Installation Data Sheet

Mini specifications

The Mega Catch Mini is a state-of-the-art mosquito trap designed for users who demand effectiveness and ease of use in pest control. Compact in size yet powerful in performance, this innovative device is perfect for both indoor and outdoor settings, making it a versatile solution for homeowners and outdoor enthusiasts alike.

One of the main features of the Mega Catch Mini is its advanced CO2 technology. This trap imitates human breath by releasing carbon dioxide, which attracts mosquitoes and other flying insects. By mimicking the natural allure of humans, the Mega Catch Mini effectively increases its catch rate, ensuring fewer pesky insects buzzing around your space.

Another notable characteristic is its silent operation. Unlike traditional bug zappers that create an audible zap sound, the Mega Catch Mini operates quietly, ensuring that your peaceful evenings are undisturbed. This makes it an ideal choice for patio gatherings, backyard barbeques, or simply enjoying a quiet night at home.

The Mega Catch Mini is also equipped with a powerful fan that draws insects into a contained trap, preventing their escape. This efficient trapping mechanism eliminates the need for toxic chemicals or harmful pesticides, making it a safer option for households with children and pets.

Easy to set up and use, the Mega Catch Mini features a simple plug-and-play design. Users can easily place it in any location for optimal performance. Its lightweight design makes it easy to move from one area to another, ensuring that you can adapt to varying outdoor conditions.

In terms of maintenance, the Mega Catch Mini is user-friendly. It has a removable catching tray that can be easily cleaned and emptied. This simplicity in maintenance ensures that users can operate the unit consistently without the hassle of complicated procedures.

Power-efficient design is another hallmark of the Mega Catch Mini. It consumes minimal energy compared to traditional insect traps, reducing your electricity bills while keeping your space free from bugs.

Overall, the Mega Catch Mini stands out as an effective, user-friendly, and environmentally-friendly solution for controlling mosquito populations. Its innovative technology, combined with practical features, makes it a top choice for anyone looking to enjoy their outdoor spaces without the nuisance of insects.
Top Page Image Contents