VI Lighting After Installation | GSW PART NO.70999 REV.G (03-12)

VI) LIGHTING AFTER INSTALLATION

WARNING:

TO AVOID POSSIBLE INJURY, FIRE AND EXPLOSION,READ THESE PRECAUTIONS BEFORE ATTEMPTING TO LIGHT OR RE- LIGHT THE PILOT. CHECK THAT THE HEATER IS FILLED WITH WATER AND THE VENTING SYSTEM IS UNOBSTRUCTED.

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A.This appliance has a pilot which must be lighted by hand. When lighting a pilot, follow these instructions exactly.

B.BEFORE OPERATING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS •Do not try to light any appliance.

•Do not touch any electric switch; do not use any phone in your building.

•Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. •If you cannot reach your gas supplier, call the fire department.

C.Use only your hand to turn the gas control knob. Never use tools. If the knob will not turn by hand, do not try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion.

D.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

BEFORE PROCEEDING WITH LIGHTING INSTRUCTIONS, PLEASE FAMILIARIZE YOURSELF WITH THE CONTROL USED ON YOUR WATER HEATER. REFER TO ILLUSTRATIONS ON PAGES 7 & 8.

WARNING: Should overheating occur or the gas supply fail to shut off, turn off the manual gas valve to the appliance.

LIGHTING INSTRUCTIONS FOR HEATER WITH “SIT” GAS CONTROLS

1.STOP! Read all safety labels on the water heater before operation.

2.Rotate the thermostat/control knob located on the gas control

clockwise to the “OFF” position.

3.Wait 5 minutes to clear out any gas. If you smell gas, STOP! Follow instruction “B” above on this page. If you do not smell gas, go to the next step.

4.To light heater, remove outer door and remove 2 screws from right side of hinged door.

5.Find pilot. Follow aluminum tube from the underside of the gas control. The pilot is in front of the burner.

6.Turn the thermostat/control knob counterclockwise to the “PILOT” position.

7.Use a lit match held securely with an extension device, or a long stem igniter. While holding the ignition source at the pilot, depress the pilot button to light the pilot.

8.Keep pilot button depressed for 60 seconds to properly heat thermocouple and activate safety controls.

9.If pilot does not remain lit, repeat steps 7 & 8.

•If the pilot will not stay lit after several attempts, turn the thermostat/control knob to “OFF” and contact your service technician.

•If the pilot button does not pop up when released, stop and immediately call your service technician or gas supplier.

10.Once the pilot is established, re-fasten 2 screws to right side of hinged door, then replace the outer door.

WARNING: FAILURE TO PROPERLY SECURE THE INNER DOOR MAY POSE A SAFETY HAZARD.

11.Turn the thermostat control knob counterclockwise to turn on the heater. Set the knob position to the “LOW” marking to start. Adjust the temperature up as required.

SIT GAS CONTROL (TOP VIEW)

To Turn Off the Gas Control

1.Rotate the thermostat control knob clockwise to the “OFF” position.

– 7 –

PART NO.70999 REV.G (03-12) specifications

The GSW PART NO. 70999 REV.G (03-12) is an exemplary product designed for high-performance application in various industrial settings. This part stands out not only for its robust construction but also for its advanced technological features, which cater to the evolving demands of modern industry.

One of the main characteristics of the GSW 70999 REV.G is its durable design, engineered to withstand challenging operational conditions. The materials used in its construction are specifically chosen for their strength and resistance to wear and corrosion, ensuring longevity and reliability in performance. This makes the component an ideal choice for applications that require consistent and dependable operation over extended periods.

In terms of technology, the GSW 70999 REV.G incorporates cutting-edge manufacturing processes that enhance its precision and functionality. The advanced machining techniques employed ensure tight tolerances and superior fit, which contribute to improved efficiency in machinery operation. This precision is particularly critical in high-speed applications, where even minor discrepancies can lead to significant performance issues.

Another key feature of the GSW 70999 REV.G is its adaptability. The part is designed with versatility in mind, allowing it to be integrated seamlessly into a variety of systems and equipment. This adaptability minimizes downtime during installation and maintenance, as users can easily incorporate the part into their existing configurations without extensive modifications.

The GSW 70999 REV.G also benefits from innovative design aspects such as ergonomic considerations, which aim to simplify handling and improve user experience. The thoughtful layout and accessibility of the component facilitate easier maintenance procedures, ultimately reducing operational costs and maximizing productivity for users.

Furthermore, GSW emphasizes sustainability in its product design and manufacturing processes. The materials are selected not only for their performance characteristics but also for their environmental impact, aligning with the industry's growing focus on sustainability and responsible sourcing.

In summary, the GSW PART NO. 70999 REV.G (03-12) is a crucial component characterized by its durability, precision, adaptability, and commitment to sustainability. It serves as an integral part in various industrial applications, promoting efficiency and reliability while catering to the increasing demands of modern technological advancement. Whether in high-speed settings or more moderate environments, this part exemplifies quality and innovation in industrial design.