GSW Comprehensive Water Heater Manual for Warranty and Installation Guidelines
Page 24

GLASS-LINED GAS FIRED COMMERCIAL WATER HEATER

WARRANTY

*THREE YEAR WARRANTY

IMPORTANT: Fill out this Warranty and keep for future reference.

MODEL NO.

SERIAL NO.

DATE INSTALLED

Owner:

INSTALLATION ADDRESS:

GSW WATER PRODUCTS COMPANY warrants that:

If within one year after original installation of a GSW water heater, any part or portion becomes defective in material or workmanship, GSW at its option, will repair or replace such part.

If the glass lined steel tank in the heater leaks due to rust or corrosion within the first *three years after the original installation, GSW will supply a complete new water heater of equivalent size and rating, and the then current model.

The replacement heater will carry a warranty equal to the unexpired portion of the original heater warranty.

A water heater should not be installed in a location where water damage can result if the water heater develops a leak. This is particularly important if the water heater is installed in a multi-story building.

In such cases, provision should be made in the installation for a means of directing to a drain pipe, any water escaping from the water heater.

The Company accepts no responsibility for damage caused by a leaking water heater.

This warranty shall only be effective while the heater remains installed in its original location in accordance with applicable plumbing and building codes, ordinances and regulations, and company instructions, and if and when:

(a)written notice is given to the Company promptly following discovery of any defect in the heater.

(b)all information which may be reasonably requested by the Company relating to the purchase, transportation, operation and installation of the heater is supplied when so requested.

(c)the defective part or heater is returned, when so requested by the Company, transportation prepaid to an address designated by the Company complete with all components properly and securely packed and if inspection by the Company proves the part or heater to be defective in workmanship or material.

(d)the heater has been subjected only to normal hot water supply conditions, that is at temperatures not exceeding the maximum setting of the thermostat and/or automatic gas shut-off control; at water pressures not exceeding the pressure rating shown on the heater, in non-corrosive atmospheres with fresh water or non-corrosive chemicals, circulating through, or stored in , the heater, when completely full of liquid and with tank free of excessive scale or lime deposits.

(e)the heater has been used only with a properly operating temperature and pressure relief valve as supplied with the heater or installed in conformity with Company instructions applicable to the specific heater model.

All repairs and replacements of parts or heaters shall be f.o.b. point of distribution and the Company shall not be liable for shipping, labour, or installation costs.

Any accident to the water heater, misuse, abuse (including freezing), alteration, modified operation or faulty repair will void this warranty.

NO OTHER WARRANTY, EXPRESSED OR IMPLIED, HAS BEEN OR WILL BE MADE ON BEHALF OF THE COMPANY WITH RESPECT TO THE HEATER OR THE INSTALLATION, OPERATION, REPAIR OR REPLACEMENT OF THE HEATER. THE COMPANY SHALL NOT BE LIABLE BY VIRTUE OF THIS WARRANTY OR OTHERWISE FOR ANY CONTINGENT DAMAGES OR OTHER CHARGES ALLEGED TO HAVE ARISEN IN CONNECTION WITH HEATERS OR PARTS CLAIMED TO BE DEFECTIVE. THE COMPANY’S WARRANTY IS A LIABILITY ONLY OF THE COMPANY AND SHALL NOT BE CONSTRUED

A LIABILITY OF ANY PERSON DEALING WITH THE HEATER. SPECIFICALLY IT SHALL NOT BE CONSTRUED AS AN IMPLIED TERM OF ANY CONTRACT OF PURCHASE AND SALE OF THE HEATER.

*TWO YEARS FOR INSTALLATION IN THE PROVINCE OF SASKATCHEWAN.

Any notice or other communication to the Company, under the terms hereof, shall be in writing and delivered personally or mailed to the Company at the following address:

COMMERCIAL

WATER HEATER WARRANTY 599 Hill Street West

Page 23

Page 23 Page 24
Image 24
Page 23 Page 24
Contents Commercial GAS Water Heater What to do if YOU Smell GASFor the Installer and User of this GAS Fired Water Heater LocationRating at tank Water supply to meter Water supply to home Water Piping Pressure Build-up in a Water SystemBTU InputPropane Venting DIA AreaSQ. Input Natural GAS Propane BTU/HRFlue Damper Damper Shaft PositionOpen Position Closed PositionConnection Diagram Appliance in Standby Condition Schematic Valve and Ignition ModuleValve and Ignition Module On Appliance Call for Heat Stage Schematic Diagram Connection Diagram Mechanical Power Venting Option Installation Check ListFor Your Safety Read Before Lighting AIR SupplyLighting Instructions White Rodgers GAS Controls Hotter Water Increases the Risk ScaldLighting Instructions For Electronic Ignition GAS Models What Do You Do If You Smell Gas?Commercial GAS E.I. Troubleshooting Sequence For Honeywell ValveMaintenance Instructions LP Propane GAS ModelsLP. GAS is Heavier than AIR Correct ANY Defects ImmediatelyTemperature Pressure Relief Valve Water Temperature RegulationTemperature General HousekeepingWater Odor Problems Cathodic ProtectionDishwashing Machine Requirements Multiple Heaters in Single SystemTWO Temperature Single Temperature or BoosterPRE-HEATER With Horizontal Storage Tank With Vertical Storage TankTemperature Pressure Relief Valve Installation Record ScheduleWarranty Three Year Warranty Model no Serial no

G65 specifications

The GSW G65 is a notable entry in the world of heavy-duty machinery, specifically designed for tasks that demand reliability and performance under challenging conditions. At the forefront of its features is a powerful engine that ensures optimal performance with robust torque delivery. This machine is equipped with a high-efficiency, state-of-the-art powertrain that maximizes productivity while minimizing fuel consumption.

One of the standout characteristics of the GSW G65 is its exceptional lifting capacity, making it suitable for a variety of applications including construction, mining, and agricultural sectors. The G65 can lift and transport heavy loads with ease, enhancing operational efficiency. Safety is paramount, and the G65 incorporates advanced stability control systems, ensuring operators can work confidently even in difficult environments.

The GSW G65 also boasts cutting-edge technologies that elevate its performance standards. A sophisticated hydraulic system allows for smooth operation, enabling precise movements necessary for intricate tasks. This hydraulic innovation provides the machine with rapid response times and reduced downtime, vital components for any project requiring efficiency.

Furthermore, the G65 is designed with operator comfort in mind. The cabin includes ergonomic seating and intuitive controls, ensuring that operators can remain productive throughout their shifts without the burden of discomfort. Additionally, with advanced noise reduction features, the cabin environment is conducive to focus and safety.

Durability is a key attribute of the GSW G65. Built with high-strength materials, the machine is designed to withstand the rigors of demanding work environments. Its maintenance-friendly design allows for easy access to components, simplifying routine checks and servicing.

In terms of technology, the G65 comes equipped with a smart monitoring system that provides real-time feedback on performance metrics, helping operators stay informed of the machine's condition. This feature enhances preventative maintenance practices, reducing the likelihood of unexpected breakdowns.

Overall, the GSW G65 stands out as a formidable machine that blends power, efficiency, and advanced technology. Its robust features and focus on operator safety and comfort make it an indispensable tool in industries that require heavy lifting and reliability. The G65 is not just a machine; it represents a commitment to excellence and innovation in heavy-duty applications.
Top Page Image Contents