GSW G65 instruction manual Flue Damper, Damper Shaft Position, Open Position, Closed Position

Page 7

FLUE DAMPER

Flue Damper Installation

For Models equipped with a flue damper, the following instructions must be followed. It is recommended to leave a minimum 24” clearance from the actuator side of the flue damper for service access.

Step 1:

Place flue damper on top pan into flue collector. The rail support must be screwed to the top pan. The three pre-drilled holes on the casing top must align with the three holes on the rail support. The rail support must fit flush with the casing top.

Step 2:

Install the draft hood which is supplied with the heater in the carton to the heater top. Fasten the draft hood with the four sheet metal screws supplied.

Step 3:

Remove junction box cover plugs. Remove flue damper cover. The wiring harness provided plugs into the four plug female molex con- nector (use strain relief connector provided). Molex plugs mate together one way only.

To manually set the damper in the open position, see diagram below.

NOTE: THE FLUE DAMPER MUST BE IN THE OPEN POSITION WHEN APPLIANCE, PILOT AND OR MAIN BURNERS ARE ON. THIS SHOULD BE CHECKED BY THE INSTALLER BEFORE LEAVING.

DAMPER SHAFT POSITION

CLOSEDOPEN

“OPEN” POSITION

CLOSEDOPEN

“CLOSED” POSITION

Flue Damper Venting

The vent pipe (flue pipe) must be installed without restriction or reduction in size. Slope the horizontal run upwards to the chimney at least 1/4” per foot. Fasten all joints with sheet metal screws. (See Figure 4)

Venting must be inspected every three months for blockage and problems due to age of the vent piping.

Damper Position Indicator

The damper position indicator can be found on the flue collar of the flue damper. (See Figure 4).

Heater Wiring

Follow local codes for all electrical work. To reduce risk of shock or possible electrocution, the heater must be electrical- ly grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI / NFPA 70.

If any of the original wiring must be replaced use only type 105oC thermoplastic or equivalent.

Figure 4

MOUNTING SCREWS (4)

DAMPER

 

POSITION

 

INDICATOR

VENT DAMPER

HOT

COLD

JUNCTION BOX

JUNCTION BOX COVER

Page 6

Page 6 Page 8
Image 7
Page 6 Page 8
Contents What to do if YOU Smell GAS Commercial GAS Water HeaterLocation For the Installer and User of this GAS Fired Water HeaterRating at tank Water supply to meter Water supply to home Pressure Build-up in a Water System Water PipingInput BTUPropane Input Natural GAS Propane BTU/HR VentingDIA Area SQ.Closed Position Flue DamperDamper Shaft Position Open PositionSchematic Valve and Ignition Module Connection Diagram Appliance in Standby ConditionValve and Ignition Module On Appliance Call for Heat Stage Schematic Diagram Connection Diagram AIR Supply Mechanical Power Venting OptionInstallation Check List For Your Safety Read Before LightingHotter Water Increases the Risk Scald Lighting Instructions White Rodgers GAS ControlsWhat Do You Do If You Smell Gas? Lighting Instructions For Electronic Ignition GAS ModelsFor Honeywell Valve Commercial GAS E.I. Troubleshooting SequenceCorrect ANY Defects Immediately Maintenance InstructionsLP Propane GAS Models LP. GAS is Heavier than AIRGeneral Housekeeping Temperature Pressure Relief ValveWater Temperature Regulation TemperatureMultiple Heaters in Single System Water Odor ProblemsCathodic Protection Dishwashing Machine RequirementsSingle Temperature or Booster TWO TemperaturePRE-HEATER With Vertical Storage Tank With Horizontal Storage TankTemperature Pressure Relief Valve Schedule Installation RecordModel no Serial no Warranty Three Year Warranty

G65 specifications

The GSW G65 is a notable entry in the world of heavy-duty machinery, specifically designed for tasks that demand reliability and performance under challenging conditions. At the forefront of its features is a powerful engine that ensures optimal performance with robust torque delivery. This machine is equipped with a high-efficiency, state-of-the-art powertrain that maximizes productivity while minimizing fuel consumption.

One of the standout characteristics of the GSW G65 is its exceptional lifting capacity, making it suitable for a variety of applications including construction, mining, and agricultural sectors. The G65 can lift and transport heavy loads with ease, enhancing operational efficiency. Safety is paramount, and the G65 incorporates advanced stability control systems, ensuring operators can work confidently even in difficult environments.

The GSW G65 also boasts cutting-edge technologies that elevate its performance standards. A sophisticated hydraulic system allows for smooth operation, enabling precise movements necessary for intricate tasks. This hydraulic innovation provides the machine with rapid response times and reduced downtime, vital components for any project requiring efficiency.

Furthermore, the G65 is designed with operator comfort in mind. The cabin includes ergonomic seating and intuitive controls, ensuring that operators can remain productive throughout their shifts without the burden of discomfort. Additionally, with advanced noise reduction features, the cabin environment is conducive to focus and safety.

Durability is a key attribute of the GSW G65. Built with high-strength materials, the machine is designed to withstand the rigors of demanding work environments. Its maintenance-friendly design allows for easy access to components, simplifying routine checks and servicing.

In terms of technology, the G65 comes equipped with a smart monitoring system that provides real-time feedback on performance metrics, helping operators stay informed of the machine's condition. This feature enhances preventative maintenance practices, reducing the likelihood of unexpected breakdowns.

Overall, the GSW G65 stands out as a formidable machine that blends power, efficiency, and advanced technology. Its robust features and focus on operator safety and comfort make it an indispensable tool in industries that require heavy lifting and reliability. The G65 is not just a machine; it represents a commitment to excellence and innovation in heavy-duty applications.
Top Page Image Contents