Exmark 000 & higher, 850 manual Set the deck in lowest cutting position

Page 16

Operation

Figure 14

Large Decks — View from Top of Blower

1.

Impeller sheave

3. Spring loaded idler

2.

Deck sheave

 

17.Position the belt cover at an angle and slide it under the mower frame (see Figure 15).

Figure 15

1. Blower

3. Mower frame

2.Belt cover

Figure 16

1. Blower

3. Deck lip

2.Belt cover

20.Install the knob and its hardware.

21.Slip the upper and the lower tubes together.

22.Insert the upper tube into the hopper seal – push in then pull out so that the seal is extended outward.

23.Align the dimple on the upper tube with the end of hopper seal and center between the two screws as shown in Figure 17.

18.Push down on the back of the cover and slide it backwards under the blower.

19.Slide the belt cover forward until it is seated under both lips on the deck.

Figure 17

1.Dimple

24.Set the deck in lowest cutting position.

25.Slide the lower tube onto the blower and attach the latches. (Make sure that the upper tube does not move out of alignment).

26.If the lower tube is replaced, drill three 7/32 inch holes in the lower tube using the upper tube holes as reference. See Figure 18.

27.Remove the tubes from unit and assemble the upper and the lower tubes using three #10-24 x 3/4 inch hex washer head screws, three #10 washers, and three #10-24 nyloc nuts. The screw head should be installed to the inside of the

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Ultra VAC All Rights Reserved Introduction Contents Safety Alert Symbol SafetySafe Operating Practices Slope Operation Maintenance and Storage Safety and Instructional Decals 103-3508 Specifications DimensionsModel Numbers SystemsProduct Overview OperationPre-Start Operating InstructionsCollection System Removal for Side Discharge Blower latch Pivot blower away from deck Collection System Installation Small Decks View from Top of Blower Set the deck in lowest cutting position Transporting Transporting a UnitLoading a Unit Rollover Protection System RopsOperation Check Blower Housing/Impeller MaintenanceCheck Bags Adjusting the Blower Drive Belt Position Check Exhaust DiverterLubricate Grease Fittings Check Condition of BeltClean Rear Screen In Hopper Clean Muffler and Rear Frame AreaClean Blower Troubleshooting Problem Possible Cause Corrective ActionExmark Commercial Attachments and Accessories Page Service Record Date Description of Work Done Service Done ByThis page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 56 pages 15.39 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 60 pages 23.73 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 40 pages 46.04 Kb Manual 52 pages 62.21 Kb Manual 44 pages 57.61 Kb Manual 32 pages 16.59 Kb Manual 60 pages 29.4 Kb Manual 24 pages 21.56 Kb Manual 48 pages 5.05 Kb

000 & higher, 850 specifications

The Exmark 850 is a top-of-the-line commercial mower, known for its durability, efficiency, and advanced features, making it a favorite among landscaping professionals. With a powerful engine and innovative technology, the Exmark 850 is designed to tackle tough mowing tasks while ensuring a high-quality cut.

One of the standout characteristics of the Exmark 850 is its robust engine performance. Powered by a reliable Kohler or Kawasaki engine, it delivers exceptional horsepower, enabling it to handle various terrains and grass types with ease. The engine is designed for fuel efficiency, allowing operators to work longer hours without frequent refueling, ultimately boosting productivity on the job.

The cutting deck of the Exmark 850 is engineered with precision, utilizing Exmark's proprietary UltraCut technology. This technology ensures that grass is cut evenly and efficiently, resulting in a clean, manicured appearance. The deck height is easily adjustable, allowing users to quickly change settings to accommodate different lawn conditions and preferences.

Another key feature is the innovative suspension system that enhances ride quality. The Exmark 850 is equipped with a heavy-duty front axle and high-performance suspension that absorbs bumps and uneven ground, allowing for a smoother mowing experience. This is especially beneficial for operators who spend long hours on the mower, reducing fatigue and improving comfort.

Ergonomics play a crucial role in the design of the Exmark 850. The operator station is thoughtfully crafted with optimal controls and comfortable seating, allowing for easy maneuverability and long-term use. The ergonomic handles and intuitive control layout make it easy for operators to navigate tricky landscapes, enhancing overall efficiency.

In terms of durability, the Exmark 850 is built to withstand the rigors of commercial use. The high-quality materials and construction ensure that this mower can handle challenging conditions, extending its lifespan and reducing maintenance needs. Additionally, Exmark offers an extensive warranty program, providing peace of mind for operators.

Safety features are also prioritized in the Exmark 850, with guards and shields designed to protect the operator while mowers are in use. These features also include emergency shut-off systems and blade brake systems, ensuring compliance with safety standards.

Overall, the Exmark 850 stands out as a high-performing, reliable, and efficient mower suitable for a variety of commercial landscaping tasks. With its powerful engine, advanced cutting technology, ergonomic design, and emphasis on durability and safety, it continues to be a top choice for professionals seeking high-quality lawn care equipment.
Top Page Image Contents