Exmark
312, 000 & higher
manual
Lazer Z E-SERIES
Troubleshooting
Specs
Schematics
Safety Alert Symbol
Dimension
Maintenance
Exmark Accessories and Options
Check Battery Charge
Adjusting the Cutting Height
Service Air Cleaner
Page 1
LAZER Z
®
E-SERIES
For Serial Nos.
312,000,000 & Higher
Lazer Z (LZE) Units
Part No.
4501-202
Rev. A
Page 1
Page 2
Image 1
Page 1
Page 2
Contents
Lazer Z E-SERIES
California
Introduction
Contents
Safety Alert Symbol
Safety
Safe Operating Practices
Training
Safety
Slope Operation
Operation
Maintenance and Storage
Using the Rollover Protection System Rops
Safety
Safety
Safety and Instructional Decals
109-7232
116-0157
116-3303 116-5944 117-2718 Message Display
Model Numbers
Specifications
Systems
Hydrostatic Ground Drive System
Seat
Tires & Wheels
Cutting Deck
Dimensions
Torque Requirements
Accessory Weight Table Worksheet
Operation
Product Overview
Controls
Motion Control Levers
Choke Control
Ignition Switch
Throttle Control
Brake Lever
Fuel Gauge
Fuel Shut-Off Valve
Drive Wheel Release Valves
Operating Instructions
Pre-Start
Starting the Engine
Open the Fuel Shut-Off Valve
Engaging the PTO
Stopping the Engine
Disengaging the PTO
Driving the Machine
Driving Forward
Adjusting the Deck Lift Foot Pedal 48 & 52 inch Decks Only
Adjusting the Cutting Height
Transporting
Adjusting the Anti-Scalp Rollers
Transporting a Unit
Loading a Unit
Recommended Maintenance Schedules
Maintenance
Check Engine Oil Level
Check Battery Charge
Do Not jump start a weak battery if these conditions exist
Recommended Jump Starting Procedure
Check Mower Blades
Check Safety Interlock System
Check Rollover Protections Systems Roll Bar Knobs
Service Air Cleaner
Check Seat Belt
Check for Loose Hardware
Check Hydraulic Oil Level
Change Engine Oil
Check Tire Pressures
Check Condition Of Belts
Lubricate Caster Wheel Hubs
Lubricate Grease Fittings
Check Spark Plugs
Lubricate Deck Lift Pivot
Change Fuel Filter
Change Hydraulic System Filter and Fluid
Check Spark Arrester if equipped
Wheel Hub Slotted Nut Torque Specification
Thread Locking Adhesives
Copper-Based Anti-seize
Deck Leveling
Adjustments
Deck Belt Tension
Pump Drive Belt Tension
Electric Clutch Adjustment
Adjusting the Parking Brake
Removing the Shim
Motion Control Linkage Adjustment
Motion Control Neutral Lock Pivot Adjustment
Motion Control Damper Adjustment
Caster Pivot Bearings Pre-Load Adjustment
Motion Control Handle Adjustment
Remove Engine Shrouds and Clean Cooling Fins
Clean Engine and Exhaust System Area
Clean Hydro Cooling Fins
Clean Grass Build-Up Under Deck
Clean Debris From Machine
Battery Disposal
Waste Disposal
Problem Possible Cause Corrective Action
Troubleshooting
See Drive Wheel Release Valves section
Troubleshooting
Pink
Schematics
Electrical Logic Schematic-Kawasaki
Electrical Logic Schematic-Kohler
Schematics
Hydraulic Diagram
Lazer Z E-Series Turf Equipment
Page
Page
Date Description of Work Done Service Done By
Service Record
Page
This page may be copied for personal use
Exmark Accessories and Options
Related manuals
Manual
60 pages
29.4 Kb
Manual
48 pages
5.05 Kb
Manual
52 pages
61.7 Kb
Manual
60 pages
62.85 Kb
Manual
52 pages
50.76 Kb
Manual
60 pages
43.2 Kb
Manual
64 pages
1.01 Kb
Manual
56 pages
15.39 Kb
Manual
28 pages
32.2 Kb
Manual
52 pages
57.34 Kb
Manual
60 pages
42.39 Kb
Manual
60 pages
23.73 Kb
Manual
40 pages
46.04 Kb
Top
Page
Image
Contents