Exmark 000 & higher, 312 manual Recommended Maintenance Schedules

Page 29

Maintenance

Maintenance

Note: Determine the left and right sides of the machine from the normal operating position.

WARNING

While maintenance or adjustments are being made, someone could start the engine. Accidental starting of the engine could seriously injure you or other bystanders.

Remove the key from the ignition switch, engage parking brake, and pull the wire(s) off the spark plug(s) before you do any maintenance. Also push the wire(s) aside so it does not accidentally contact the spark plug(s).

WARNING

The engine can become very hot. Touching a hot engine can cause severe burns.

Allow the engine to cool completely before service or making repairs around the engine area.

Recommended Maintenance Schedule(s)

Maintenance Service

Maintenance Procedure

Interval

 

 

 

 

 

After the first 5 hours

•

Change the engine oil.

 

 

 

• Check the wheel hub slotted nut torque specifications.

After the first 100 hours

•

Check the wheel lug nuts.

 

• Check the park brake adjustment.

 

 

 

After the first 250 hours

•

Change the hydraulic filter and fluid.

 

 

 

• Check the engine oil level.

 

•

Check the mower blades.

 

• Check the safety interlock system.

 

• Check the rollover protections systems (roll bar) knobs.

Before each use or daily

• Check the seat belt.

• Check for loose hardware.

 

 

• Clean the engine and exhaust system area.

 

• Clean the hydro cooling fins.

 

• Clean the grass and debris build-up from the machine and cutting deck.

 

• Clean the grass build-up from under the cutting deck.

 

 

 

• Check the hydraulic oil level.

Every 50 hours

• Check the tire pressures.

• Check the condition of the belts.

 

 

• Check spark arrester (if equipped).

 

 

 

• Change the engine oil. (May need more often under severe conditions.)

Every 100 hours

•

Lubricate the deck lift pivots.

 

• Remove the engine shrouds and clean the cooling fins.

 

 

 

Every 200 hours

•

Check the spark plugs.

 

 

 

• Replace the primary air cleaner element — check secondary air cleaner element; replace if

Every 250 hours

 

dirty. (May need more often under severe conditions. See the Engine Owner's Manual for

 

 

additional information.)

 

 

 

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Lazer Z E-SERIES California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingSafety Slope Operation OperationMaintenance and Storage Using the Rollover Protection System RopsSafety Safety Safety and Instructional Decals 109-7232 116-0157 116-3303 116-5944 117-2718 Message Display Systems SpecificationsModel Numbers Hydrostatic Ground Drive System SeatTires & Wheels Cutting DeckDimensions Torque Requirements Accessory Weight Table WorksheetOperation Product OverviewControls Motion Control LeversChoke Control Ignition SwitchThrottle Control Brake LeverDrive Wheel Release Valves Fuel Shut-Off ValveFuel Gauge Operating Instructions Pre-StartEngaging the PTO Open the Fuel Shut-Off ValveStarting the Engine Driving the Machine Disengaging the PTOStopping the Engine Driving Forward Adjusting the Deck Lift Foot Pedal 48 & 52 inch Decks Only Adjusting the Cutting HeightTransporting a Unit Adjusting the Anti-Scalp RollersTransporting Loading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeDo Not jump start a weak battery if these conditions exist Recommended Jump Starting ProcedureCheck Mower Blades Check Safety Interlock SystemCheck Rollover Protections Systems Roll Bar Knobs Service Air CleanerCheck Seat Belt Check for Loose HardwareCheck Hydraulic Oil Level Change Engine OilCheck Tire Pressures Check Condition Of BeltsLubricate Caster Wheel Hubs Lubricate Grease FittingsCheck Spark Plugs Lubricate Deck Lift PivotChange Fuel Filter Change Hydraulic System Filter and FluidCheck Spark Arrester if equipped Wheel Hub Slotted Nut Torque SpecificationThread Locking Adhesives Copper-Based Anti-seizeDeck Leveling AdjustmentsDeck Belt Tension Pump Drive Belt TensionElectric Clutch Adjustment Adjusting the Parking BrakeRemoving the Shim Motion Control Linkage Adjustment Motion Control Neutral Lock Pivot Adjustment Motion Control Damper AdjustmentCaster Pivot Bearings Pre-Load Adjustment Motion Control Handle AdjustmentClean Hydro Cooling Fins Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Grass Build-Up Under Deck Clean Debris From MachineBattery Disposal Waste DisposalProblem Possible Cause Corrective Action TroubleshootingSee Drive Wheel Release Valves section Troubleshooting Pink SchematicsElectrical Logic Schematic-Kawasaki Electrical Logic Schematic-Kohler SchematicsHydraulic Diagram Lazer Z E-Series Turf Equipment Page Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use Exmark Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 43.2 Kb Manual 64 pages 1.01 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 60 pages 23.73 Kb Manual 40 pages 46.04 Kb

0, 312, 000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.
Top Page Image Contents