Exmark 000 & higher, 312 manual Adjustments, Deck Leveling

Page 38

Maintenance

Adjustments

Note: Disengage PTO, shut off engine, wait for all moving parts to stop, engage parking brake, and remove key before servicing, cleaning, or making any adjustments to the unit.

CAUTION

Raising the mower deck for service or maintenance relying solely on mechanical or hydraulic jacks could be dangerous. The mechanical or hydraulic jacks may not be enough support or may malfunction allowing the unit to fall, which could cause injury.

Do Not rely solely on mechanical or hydraulic jacks for support. Use adequate jack stands or equivalent support.

Deck Leveling

1.Position the mower on a flat surface.

2.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

3.Check the tire pressure in the drive tires. Proper inflation pressure for tires is 13 psi (90 kPa). Adjust if necessary.

4.Position the transport lock in the latching position.

5.Push the foot pedal all the way forward and the deck will latch at the 4 1/2 inch (11.4 cm) transport position (Figure 26).

Figure 26

1. Foot lever

3. Transport lock

2.Height of cut pin

6.Insert the height adjustment pin into the 3 inch (7.6 cm) cutting height location.

7.Release the transport lock and allow the deck to lower to the cutting height.

8.Raise the discharge deflector.

9.Measure from the level surface to the front tip of the center blade. The measurement should read 3 inches (7.6 cm).

Note: In most conditions, the back tips on the side blades should be adjusted 1/4 inch (6.4 mm) higher than the front.

38

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Lazer Z E-SERIES California Introduction Contents Safe Operating Practices SafetySafety Alert Symbol TrainingSafety Operation Slope OperationUsing the Rollover Protection System Rops Maintenance and StorageSafety Safety Safety and Instructional Decals 109-7232 116-0157 116-3303 116-5944 117-2718 Message Display Systems SpecificationsModel Numbers Tires & Wheels SeatHydrostatic Ground Drive System Cutting DeckDimensions Accessory Weight Table Worksheet Torque RequirementsControls Product OverviewOperation Motion Control LeversThrottle Control Ignition SwitchChoke Control Brake LeverDrive Wheel Release Valves Fuel Shut-Off ValveFuel Gauge Pre-Start Operating InstructionsEngaging the PTO Open the Fuel Shut-Off ValveStarting the Engine Driving the Machine Disengaging the PTOStopping the Engine Driving Forward Adjusting the Cutting Height Adjusting the Deck Lift Foot Pedal 48 & 52 inch Decks OnlyTransporting a Unit Adjusting the Anti-Scalp RollersTransporting Loading a Unit Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelRecommended Jump Starting Procedure Do Not jump start a weak battery if these conditions existCheck Safety Interlock System Check Mower BladesCheck Seat Belt Service Air CleanerCheck Rollover Protections Systems Roll Bar Knobs Check for Loose HardwareCheck Tire Pressures Change Engine OilCheck Hydraulic Oil Level Check Condition Of BeltsLubricate Grease Fittings Lubricate Caster Wheel HubsChange Fuel Filter Lubricate Deck Lift PivotCheck Spark Plugs Change Hydraulic System Filter and FluidThread Locking Adhesives Wheel Hub Slotted Nut Torque SpecificationCheck Spark Arrester if equipped Copper-Based Anti-seizeAdjustments Deck LevelingPump Drive Belt Tension Deck Belt TensionAdjusting the Parking Brake Electric Clutch AdjustmentRemoving the Shim Motion Control Linkage Adjustment Motion Control Damper Adjustment Motion Control Neutral Lock Pivot AdjustmentMotion Control Handle Adjustment Caster Pivot Bearings Pre-Load AdjustmentClean Hydro Cooling Fins Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Battery Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Waste DisposalTroubleshooting Problem Possible Cause Corrective ActionSee Drive Wheel Release Valves section Troubleshooting Schematics PinkElectrical Logic Schematic-Kawasaki Schematics Electrical Logic Schematic-KohlerHydraulic Diagram Lazer Z E-Series Turf Equipment Page Page Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use Exmark Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 43.2 Kb Manual 64 pages 1.01 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 60 pages 23.73 Kb Manual 40 pages 46.04 Kb

0, 312, 000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.
Top Page Image Contents