Exmark
920, 000 & higher
manual
Vantage
Troubleshooting
Specs
Lubrication Chart
Safety Alert Symbol
Low Voltage Indicator
Dimension
Maintenance
Check Battery Charge
Adjusting the Cutting Height
Service Air Cleaner
Page 1
VANTAGE™
36 INCH MODELS
For Serial Nos.
920,000 & Higher
Part No.
4500-897
Rev. A
Page 1
Page 2
Image 1
Page 1
Page 2
Contents
Vantage
California
Introduction
Contents
Safety Alert Symbol
Safety
Safe Operating Practices
Training
Safety
Slope Operation
Operation
Maintenance and Storage
Safety
Safety and Instructional Decals
116-0404 116-3267 116-3290 116-4270 116-4271 116-4298
116-1887
Model Numbers
Specifications
Systems
Torque Requirements
Dimensions
Controls
Product Overview Operation
Motion Control Levers
Choke Control
Ignition Switch
Throttle Control
Front Reference/Speed Control Bar
Low Voltage Indicator
PTO Engagement Switch
Hour Meter
Fuel Shut-Off Valve
Operating Instructions
Pre-Start
Open the Fuel Shut-Off Valve
Starting the Engine
Stopping the Engine
Disengaging the PTO
Driving the Machine
Driving Forward
Driving in Reverse
Adjusting the Front Reference/Speed Control Bar
Operating the Machine with the Platform Up
Operating the Platform
Operating the Machine with the Platform Down
Adjusting the Cutting Height
Transporting a Unit
Transporting
Loading a Unit
Recommended Maintenance Schedules
Maintenance
Recommended Jump Starting Procedure
Check Battery Charge
Check Engine Oil Level
Proposition 65 Warning
Do Not jump start a weak battery if these conditions exist
Release the Cushion for Rear Access
Remove key. Engage parking brake
Check Mower Blades
Service Air Cleaner
Check Safety Interlock System
Checking the Safety Interlock System
Check for Loose Hardware
Check Hydraulic Oil Level
Change Engine Oil
Check Tire Pressures
Check Condition Of Belts
Lubricate Caster Wheel Hubs
Lubrication Chart
Change Fuel Filter
Check Spark Plugs
Change Hydraulic System Filter and Fluid
Level
Hydraulic System Air Purge
Wheel Hub Nut Torque Specification
Check Spark Arrester if equipped
Mobil HTS Grease Or Food-Grade Anti-seize
Thread Locking Adhesives
Copper-Based Anti-seize
Dielectric Grease
Deck Leveling
Adjustments
Park Brake Adjustment
Overall Height Adjustment
Deck Lift Handle Force
Pump Drive Belt Tension
Removing the Shim
Electric Clutch Adjustment
Forward Speed Adjustment
Motion Control Tracking Adjustment
Adjust RH Motion Control Handle Position
Clean Engine and Exhaust System Area
Caster Pivot Bearings Pre-Load Adjustment
Remove Engine Shrouds and Clean Cooling Fins
Clean Debris From Machine
Battery Disposal
Clean Grass Build-Up Under Deck
Waste Disposal
Motor Oil Disposal
Problem Possible Cause Corrective Action
Troubleshooting
Troubleshooting
Troubleshooting
Electrical Diagram
Schematics
Electrical Schematic
Hydraulic Diagram
General Warranty Conditions and Products Covered
Date Description of Work Done Service Done By
Service Record
Page
This page may be copied for personal use
See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual
60 pages
42.39 Kb
Manual
60 pages
43.2 Kb
Manual
64 pages
37.72 Kb
Manual
52 pages
8.82 Kb
Manual
56 pages
15.39 Kb
Manual
28 pages
32.2 Kb
Manual
52 pages
61.7 Kb
Manual
60 pages
62.85 Kb
Manual
60 pages
23.73 Kb
Manual
52 pages
50.76 Kb
Manual
60 pages
57.72 Kb
Manual
40 pages
46.04 Kb
Top
Page
Image
Contents