Exmark 000 & higher, 920 manual Adjustments, Deck Leveling

Page 34

Maintenance

Adjustments

Note: Disengage PTO, shut off engine, wait for all moving parts to stop, engage parking brake, and remove key before servicing, cleaning, or making any adjustments to the unit.

CAUTION

Raising the mower for service or maintenance relying solely on mechanical or hydraulic jacks could be dangerous. The mechanical or hydraulic jacks may not be enough support or may malfunction allowing the unit to fall, which could cause injury.

Do Not rely solely on mechanical or hydraulic jacks for support. Use adequate jack stands or equivalent support.

Deck Leveling

Note: Small adjustments can be accomplished by increasing the tire pressure in the tire on the low side.

1.Park the machine on a level surface and disengage the blade control switch.

2.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

3.Check the air pressure in the drive tires. If needed, adjust to the recommended inflation; refer to Checking the Tire Pressure in Drive System Maintenance section.

4.Set the height of cut lever to the 3 inch (7.6 cm) position.

5.Raise the discharge deflector.

6.Carefully rotate the blades front to rear. Measure from the tip of the front blade to the level surface (Figure 22). The blades should measure 3 inches (7.6 cm).

Note: In most conditions, the back tips should be adjusted 1/4 inch (6.4 mm) higher than the front.

Figure 22

1.

3 1/4 inches (8.3 cm)

4.

3 inches (7.6 cm)

2.

Back blade tip

5.

Level surface

3.Front blade tip

7.Use the fine tune adjustments on the front deck lift arms to adjust the height of the front blade tips. Loosen the whizlock nut on the side of the yoke and the jam nut on top. Fine tune the screw adjuster by turning it to get 3 inches (7.6 mm) height. To increase the height, turn the adjuster screw clockwise; to decrease, turn counterclockwise (see Figure Figure 23).

Figure 23

1.

Adjuster screw

3.

Whizlock nut

2.

Jam nut

4.

Yoke

 

 

 

 

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Vantage California Introduction Contents Safe Operating Practices SafetySafety Alert Symbol TrainingSafety Operation Slope OperationMaintenance and Storage Safety Safety and Instructional Decals 116-0404 116-3267 116-3290 116-4270 116-4271 116-4298 116-1887 Model Numbers SpecificationsSystems Dimensions Torque RequirementsControls Product Overview OperationMotion Control Levers Throttle Control Ignition SwitchChoke Control Front Reference/Speed Control BarHour Meter PTO Engagement SwitchLow Voltage Indicator Fuel Shut-Off ValveOpen the Fuel Shut-Off Valve Pre-StartOperating Instructions Starting the EngineDriving the Machine Disengaging the PTOStopping the Engine Driving ForwardAdjusting the Front Reference/Speed Control Bar Driving in ReverseOperating the Platform Operating the Machine with the Platform UpAdjusting the Cutting Height Operating the Machine with the Platform DownTransporting a Unit TransportingLoading a Unit Maintenance Recommended Maintenance SchedulesCheck Engine Oil Level Check Battery ChargeRecommended Jump Starting Procedure Proposition 65 WarningRelease the Cushion for Rear Access Do Not jump start a weak battery if these conditions existCheck Mower Blades Remove key. Engage parking brakeChecking the Safety Interlock System Check Safety Interlock SystemService Air Cleaner Check for Loose HardwareCheck Tire Pressures Change Engine OilCheck Hydraulic Oil Level Check Condition Of BeltsLubrication Chart Lubricate Caster Wheel HubsChange Hydraulic System Filter and Fluid Check Spark PlugsChange Fuel Filter LevelHydraulic System Air Purge Wheel Hub Nut Torque SpecificationCheck Spark Arrester if equipped Copper-Based Anti-seize Thread Locking AdhesivesMobil HTS Grease Or Food-Grade Anti-seize Dielectric GreaseAdjustments Deck LevelingDeck Lift Handle Force Overall Height AdjustmentPark Brake Adjustment Pump Drive Belt TensionElectric Clutch Adjustment Removing the ShimForward Speed Adjustment Motion Control Tracking Adjustment Adjust RH Motion Control Handle Position Remove Engine Shrouds and Clean Cooling Fins Caster Pivot Bearings Pre-Load AdjustmentClean Engine and Exhaust System Area Clean Debris From MachineWaste Disposal Clean Grass Build-Up Under DeckBattery Disposal Motor Oil DisposalTroubleshooting Problem Possible Cause Corrective ActionTroubleshooting Troubleshooting Schematics Electrical DiagramElectrical Schematic Hydraulic Diagram General Warranty Conditions and Products Covered Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 60 pages 42.39 Kb Manual 60 pages 43.2 Kb Manual 64 pages 37.72 Kb Manual 52 pages 8.82 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 60 pages 23.73 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 40 pages 46.04 Kb

920, 000 & higher specifications

The Exmark 920 is an exceptional piece of equipment tailored for professionals and enthusiasts alike. Designed with an emphasis on performance and reliability, this mower embodies the pinnacle of lawn care technology. Known for its robust construction, the Exmark 920 is equipped with a powerful engine, ensuring efficient and effective mowing even in demanding conditions.

One of the standout features of the Exmark 920 is its cutting deck. With a 52-inch or 60-inch mower deck option, it allows users to cover a large mowing area quickly. The deck is crafted from high-strength steel, providing durability and longevity while maintaining a lightweight design that enhances maneuverability. Innovative blade design promotes superior airflow for an even cut, preventing clumping and ensuring a polished finish across various grass types.

The Exmark 920 utilizes advanced technology, including the innovative RED Technology, which enhances engine performance by optimizing power consumption. This results in reduced fuel consumption while maintaining the required power output for demanding tasks. Additionally, the mower’s intuitive controls include a user-friendly interface, allowing for easy adjustments and settings, catering to the varying needs of different lawn types and conditions.

Another notable feature of the Exmark 920 is its all-day comfort design. With an ergonomic seat and advanced suspension system, operators can tackle long mowing sessions without discomfort. The padded seat is adjustable, providing maximum support to minimize fatigue, while the suspension system absorbs bumps and uneven terrain for a smoother ride.

Furthermore, the Exmark 920 prioritizes serviceability. Easy access points for maintenance and a well-designed layout ensure that routine tasks, such as oil changes and blade replacements, can be completed efficiently. The model also comes equipped with LED headlights for improved visibility during early morning or late evening mowing.

In summary, the Exmark 920 is a sophisticated mower combining power, advanced technology, and design for comfort and utility. Its high-performance engine, durable cutting deck, user-friendly controls, and serviceable layout make it an ideal choice for anyone seeking to achieve a well-manicured lawn with professional results. Whether for commercial or residential use, the Exmark 920 stands out as a leading option in the market, enabling users to tackle any mowing challenge with confidence and ease.
Top Page Image Contents