Exmark 000 & higher, 920 manual Motion Control Tracking Adjustment

Page 38

Maintenance

machine — see Figure 31). Rotate the turnbuckle counterclockwise (as viewed from the top of the machine) until there is a gap between the control lever and the front reference/speed control bar.

Figure 31

1. Lock nut

3. Lock nut (LH thread)

2.Turnbuckle

7.With the RH control lever all the way forward, make sure the RH pump arm bottoms out on the forward stop, located by the hydraulic hoses, as shown in Figure 32.

Motion Control Tracking Adjustment

If the machine travels or pulls to one side when the motion control levers are in the full forward position, adjust the tracking.

1.Push both control levers forward the same distance.

2.Check if the machine pulls to one side. If it does, stop the machine and set the parking brake.

3.Release the rear cushion from the rear of the machine.

4.Place the front reference/speed control bar in the maximum forward position. See Adjusting the Front Reference/Speed Control Bar in Operation.

5.Rotate the adjustment rod on the LH side of the machine. Looking down towards the adjustment rod, rotate clockwise to decrease speed or counterclockwise to increase speed (see Figure 33).

 

 

Figure 32

 

 

Figure 33

 

 

1.

Rotate to increase speed

1.

RH control lever

3. RH pump arm

2.

Turnbuckle

2.

Forward stop

 

 

3.

Rotate to decrease speed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8.Holding the RH control lever forward, rotate the turnbuckle clockwise until there is a minimal gap or contact between the RH control lever and the front reference/speed control bar.

9.Tighten the jam nuts.

10.Reinstall the rear cushion.

6.Drive the machine and check the full forward tracking.

7.Repeat steps 5 and 6 until desired tracking is obtained.

8.Reinstall the rear cushion.

38

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Vantage California Introduction Contents Safe Operating Practices SafetySafety Alert Symbol TrainingSafety Operation Slope OperationMaintenance and Storage Safety Safety and Instructional Decals 116-0404 116-3267 116-3290 116-4270 116-4271 116-4298 116-1887 Systems SpecificationsModel Numbers Dimensions Torque RequirementsMotion Control Levers Product Overview OperationControls Throttle Control Ignition SwitchChoke Control Front Reference/Speed Control BarHour Meter PTO Engagement SwitchLow Voltage Indicator Fuel Shut-Off ValveOpen the Fuel Shut-Off Valve Pre-StartOperating Instructions Starting the EngineDriving the Machine Disengaging the PTOStopping the Engine Driving ForwardAdjusting the Front Reference/Speed Control Bar Driving in ReverseOperating the Platform Operating the Machine with the Platform UpAdjusting the Cutting Height Operating the Machine with the Platform DownLoading a Unit TransportingTransporting a Unit Maintenance Recommended Maintenance SchedulesCheck Engine Oil Level Check Battery ChargeRecommended Jump Starting Procedure Proposition 65 WarningRelease the Cushion for Rear Access Do Not jump start a weak battery if these conditions existCheck Mower Blades Remove key. Engage parking brakeChecking the Safety Interlock System Check Safety Interlock SystemService Air Cleaner Check for Loose HardwareCheck Tire Pressures Change Engine OilCheck Hydraulic Oil Level Check Condition Of BeltsLubrication Chart Lubricate Caster Wheel HubsChange Hydraulic System Filter and Fluid Check Spark PlugsChange Fuel Filter LevelCheck Spark Arrester if equipped Wheel Hub Nut Torque SpecificationHydraulic System Air Purge Copper-Based Anti-seize Thread Locking AdhesivesMobil HTS Grease Or Food-Grade Anti-seize Dielectric GreaseAdjustments Deck LevelingDeck Lift Handle Force Overall Height AdjustmentPark Brake Adjustment Pump Drive Belt TensionElectric Clutch Adjustment Removing the ShimForward Speed Adjustment Motion Control Tracking Adjustment Adjust RH Motion Control Handle Position Remove Engine Shrouds and Clean Cooling Fins Caster Pivot Bearings Pre-Load AdjustmentClean Engine and Exhaust System Area Clean Debris From MachineWaste Disposal Clean Grass Build-Up Under DeckBattery Disposal Motor Oil DisposalTroubleshooting Problem Possible Cause Corrective ActionTroubleshooting Troubleshooting Schematics Electrical DiagramElectrical Schematic Hydraulic Diagram General Warranty Conditions and Products Covered Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 60 pages 42.39 Kb Manual 60 pages 43.2 Kb Manual 64 pages 37.72 Kb Manual 52 pages 8.82 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 60 pages 23.73 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 40 pages 46.04 Kb

920, 000 & higher specifications

The Exmark 920 is an exceptional piece of equipment tailored for professionals and enthusiasts alike. Designed with an emphasis on performance and reliability, this mower embodies the pinnacle of lawn care technology. Known for its robust construction, the Exmark 920 is equipped with a powerful engine, ensuring efficient and effective mowing even in demanding conditions.

One of the standout features of the Exmark 920 is its cutting deck. With a 52-inch or 60-inch mower deck option, it allows users to cover a large mowing area quickly. The deck is crafted from high-strength steel, providing durability and longevity while maintaining a lightweight design that enhances maneuverability. Innovative blade design promotes superior airflow for an even cut, preventing clumping and ensuring a polished finish across various grass types.

The Exmark 920 utilizes advanced technology, including the innovative RED Technology, which enhances engine performance by optimizing power consumption. This results in reduced fuel consumption while maintaining the required power output for demanding tasks. Additionally, the mower’s intuitive controls include a user-friendly interface, allowing for easy adjustments and settings, catering to the varying needs of different lawn types and conditions.

Another notable feature of the Exmark 920 is its all-day comfort design. With an ergonomic seat and advanced suspension system, operators can tackle long mowing sessions without discomfort. The padded seat is adjustable, providing maximum support to minimize fatigue, while the suspension system absorbs bumps and uneven terrain for a smoother ride.

Furthermore, the Exmark 920 prioritizes serviceability. Easy access points for maintenance and a well-designed layout ensure that routine tasks, such as oil changes and blade replacements, can be completed efficiently. The model also comes equipped with LED headlights for improved visibility during early morning or late evening mowing.

In summary, the Exmark 920 is a sophisticated mower combining power, advanced technology, and design for comfort and utility. Its high-performance engine, durable cutting deck, user-friendly controls, and serviceable layout make it an ideal choice for anyone seeking to achieve a well-manicured lawn with professional results. Whether for commercial or residential use, the Exmark 920 stands out as a leading option in the market, enabling users to tackle any mowing challenge with confidence and ease.
Top Page Image Contents