Exmark 920, 000 & higher manual Adjust RH Motion Control Handle Position

Page 39

Maintenance

Adjust RH Motion Control Handle Position

If the motion control levers do not align horizontally, adjust the right side motion control lever.

Note: Adjust the horizontal alignment before the front to back alignment.

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Push the right motion control lever down out of locked neutral position.

3.Check if it aligns horizontally with the left motion control lever.

Figure 34

1.LH Motion control lever

2.RH Motion control lever

3.RH Motion control lever in PTO disengaged position

4.Check the horizontal alignment here

4.To adjust the right motion control lever horizontally, the cam needs to be adjusted.

5.Release the cushion from the rear of the machine.

6.Loosen the nut and bolt holding the cam.

7.Adjust the cam until it aligns with the left motion control lever and tighten the nut and bolt for the cam.

Figure 35

1.Switch screws

2.Nut and bolt

3.Cam

4.Front reference/speed control handle

8.After the cam is adjusted, the lever switch needs to be checked.

9.Check the gap between the control lever and switch as shown in Figure 36. The gap needs to be an 1/8 inch (3mm) with the right motion control lever in the neutral, operate position.

Figure 36

1.Switch

2.Cam

3.Right motion control lever in the neutral operate position

4.1/8 inch (3mm)

10.If needed, loosen the screws holding the switch and adjust the switch.

11.Tighten the switch screws.

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Vantage California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Slope Operation OperationMaintenance and Storage Safety Safety and Instructional Decals 116-0404 116-3267 116-3290 116-4270 116-4271 116-4298 116-1887 Specifications Model NumbersSystems Torque Requirements DimensionsProduct Overview Operation ControlsMotion Control Levers Front Reference/Speed Control Bar Ignition SwitchChoke Control Throttle ControlFuel Shut-Off Valve PTO Engagement SwitchLow Voltage Indicator Hour MeterStarting the Engine Pre-StartOperating Instructions Open the Fuel Shut-Off ValveDriving Forward Disengaging the PTOStopping the Engine Driving the MachineDriving in Reverse Adjusting the Front Reference/Speed Control BarOperating the Machine with the Platform Up Operating the PlatformOperating the Machine with the Platform Down Adjusting the Cutting HeightTransporting Transporting a UnitLoading a Unit Recommended Maintenance Schedules MaintenanceProposition 65 Warning Check Battery ChargeRecommended Jump Starting Procedure Check Engine Oil LevelDo Not jump start a weak battery if these conditions exist Release the Cushion for Rear AccessRemove key. Engage parking brake Check Mower BladesCheck for Loose Hardware Check Safety Interlock SystemService Air Cleaner Checking the Safety Interlock SystemCheck Condition Of Belts Change Engine OilCheck Hydraulic Oil Level Check Tire PressuresLubricate Caster Wheel Hubs Lubrication ChartLevel Check Spark PlugsChange Fuel Filter Change Hydraulic System Filter and FluidWheel Hub Nut Torque Specification Hydraulic System Air PurgeCheck Spark Arrester if equipped Dielectric Grease Thread Locking AdhesivesMobil HTS Grease Or Food-Grade Anti-seize Copper-Based Anti-seizeDeck Leveling AdjustmentsPump Drive Belt Tension Overall Height AdjustmentPark Brake Adjustment Deck Lift Handle ForceRemoving the Shim Electric Clutch AdjustmentForward Speed Adjustment Motion Control Tracking Adjustment Adjust RH Motion Control Handle Position Clean Debris From Machine Caster Pivot Bearings Pre-Load AdjustmentClean Engine and Exhaust System Area Remove Engine Shrouds and Clean Cooling FinsMotor Oil Disposal Clean Grass Build-Up Under DeckBattery Disposal Waste DisposalProblem Possible Cause Corrective Action TroubleshootingTroubleshooting Troubleshooting Electrical Diagram SchematicsElectrical Schematic Hydraulic Diagram General Warranty Conditions and Products Covered Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 60 pages 42.39 Kb Manual 60 pages 43.2 Kb Manual 64 pages 37.72 Kb Manual 52 pages 8.82 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 60 pages 23.73 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 40 pages 46.04 Kb

920, 000 & higher specifications

The Exmark 920 is an exceptional piece of equipment tailored for professionals and enthusiasts alike. Designed with an emphasis on performance and reliability, this mower embodies the pinnacle of lawn care technology. Known for its robust construction, the Exmark 920 is equipped with a powerful engine, ensuring efficient and effective mowing even in demanding conditions.

One of the standout features of the Exmark 920 is its cutting deck. With a 52-inch or 60-inch mower deck option, it allows users to cover a large mowing area quickly. The deck is crafted from high-strength steel, providing durability and longevity while maintaining a lightweight design that enhances maneuverability. Innovative blade design promotes superior airflow for an even cut, preventing clumping and ensuring a polished finish across various grass types.

The Exmark 920 utilizes advanced technology, including the innovative RED Technology, which enhances engine performance by optimizing power consumption. This results in reduced fuel consumption while maintaining the required power output for demanding tasks. Additionally, the mower’s intuitive controls include a user-friendly interface, allowing for easy adjustments and settings, catering to the varying needs of different lawn types and conditions.

Another notable feature of the Exmark 920 is its all-day comfort design. With an ergonomic seat and advanced suspension system, operators can tackle long mowing sessions without discomfort. The padded seat is adjustable, providing maximum support to minimize fatigue, while the suspension system absorbs bumps and uneven terrain for a smoother ride.

Furthermore, the Exmark 920 prioritizes serviceability. Easy access points for maintenance and a well-designed layout ensure that routine tasks, such as oil changes and blade replacements, can be completed efficiently. The model also comes equipped with LED headlights for improved visibility during early morning or late evening mowing.

In summary, the Exmark 920 is a sophisticated mower combining power, advanced technology, and design for comfort and utility. Its high-performance engine, durable cutting deck, user-friendly controls, and serviceable layout make it an ideal choice for anyone seeking to achieve a well-manicured lawn with professional results. Whether for commercial or residential use, the Exmark 920 stands out as a leading option in the market, enabling users to tackle any mowing challenge with confidence and ease.
Top Page Image Contents