Exmark 920, 000 & higher manual Change Engine Oil, Check Hydraulic Oil Level, Check Tire Pressures

Page 29

Maintenance

need more often under severe conditions. See the Engine manual for additional information.)

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.See the Engine Owner’s Manual for maintenance instructions.

Change Engine Oil

Service Interval: After the first 5 hours

Every 100 hours (May need more often under severe conditions.)

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Drain oil while engine is warm from operation.

3.The oil drain valve is located on the left side of the engine.

Place the pan under the machine to catch the oil. Install the clear plastic tube, located in the literature pack, onto the oil drain valve. Loosen the oil drain valve and allow the oil to drain.

Tighten the oil drain valve and remove and retain the clear plastic tube.

4.Replace the oil filter per the Engine Owner’s Manual. Clean around the oil filter and carefully remove the filter by unscrewing it. Make sure no oil drains onto the belt drive or clutch through the holes in the engine deck. Before the new filter is installed, apply a thin coating of Exmark 4–Cycle Premium Engine Oil on the surface of the rubber seal. Turn filter clockwise until rubber seal contacts the filter adapter, then tighten filter an additional 2/3 to 3/4 turn.

5.Clean around oil fill cap and remove cap. Fill to specified capacity and replace cap.

6.Use oil recommended in the Check Engine Oil Level section. Do Not overfill. Start the engine and check for leaks. Stop engine and recheck oil level.

7.Wipe up any spilled oil from engine deck mounting surfaces.

Check Hydraulic Oil Level

Service Interval: Every 40 hours

1.Stop engine and wait for all moving parts to stop, and remove key. Engage parking brake.

2.Clean area around hydraulic reservoir cap and remove cap. Oil level should be to the top of the baffle inside the tank. If not, add oil. Use Exmark Premium Hydro Oil. Replace hydraulic reservoir cap and tighten until snug. Do Not overtighten.

Note: The baffle is labeled “HOT” and “COLD”. The oil level varies with the temperature of the oil. The “HOT” level shows the level of oil when it is at 225°F (107°C). The “COLD” level shows the level of the oil when it is at 75°F (24°C). Fill to the appropriate level depending upon the temperature of the oil. For example: If the oil is about 150°F (65°C), fill to halfway between the “HOT” and “COLD” levels. If the oil is at room temperature (about 75°F (24°C)), fill only to the “COLD” level.

Check Tire Pressures

Service Interval: Every 50 hours

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Check tire pressure in drive tires.

3.Inflate drive tires to 12–14 psi (83–97 kPa).

4.Semi-pneumatic caster tires do not need to be inflated.

Check Condition Of Belts

Service Interval: Every 40 hours

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Look on the top side of the cutting deck to check the mower blade drive belt condition.

3.Look under the engine deck to check the pump drive belt condition.

4.Check all idler arms to be sure they pivot freely.

Lubricate Grease Fittings

Note: See chart for service intervals.

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Lubricate fittings with NGLI grade #2 multi-purpose gun grease.

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Vantage California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingSafety Slope Operation OperationMaintenance and Storage Safety Safety and Instructional Decals 116-0404 116-3267 116-3290 116-4270 116-4271 116-4298 116-1887 Systems SpecificationsModel Numbers Torque Requirements DimensionsMotion Control Levers Product Overview OperationControls Choke Control Ignition SwitchThrottle Control Front Reference/Speed Control BarLow Voltage Indicator PTO Engagement SwitchHour Meter Fuel Shut-Off ValveOperating Instructions Pre-StartOpen the Fuel Shut-Off Valve Starting the EngineStopping the Engine Disengaging the PTODriving the Machine Driving ForwardDriving in Reverse Adjusting the Front Reference/Speed Control BarOperating the Machine with the Platform Up Operating the PlatformOperating the Machine with the Platform Down Adjusting the Cutting HeightLoading a Unit TransportingTransporting a Unit Recommended Maintenance Schedules MaintenanceRecommended Jump Starting Procedure Check Battery ChargeCheck Engine Oil Level Proposition 65 WarningDo Not jump start a weak battery if these conditions exist Release the Cushion for Rear AccessRemove key. Engage parking brake Check Mower BladesService Air Cleaner Check Safety Interlock SystemChecking the Safety Interlock System Check for Loose HardwareCheck Hydraulic Oil Level Change Engine OilCheck Tire Pressures Check Condition Of BeltsLubricate Caster Wheel Hubs Lubrication ChartChange Fuel Filter Check Spark PlugsChange Hydraulic System Filter and Fluid LevelCheck Spark Arrester if equipped Wheel Hub Nut Torque SpecificationHydraulic System Air Purge Mobil HTS Grease Or Food-Grade Anti-seize Thread Locking AdhesivesCopper-Based Anti-seize Dielectric GreaseDeck Leveling AdjustmentsPark Brake Adjustment Overall Height AdjustmentDeck Lift Handle Force Pump Drive Belt TensionRemoving the Shim Electric Clutch AdjustmentForward Speed Adjustment Motion Control Tracking Adjustment Adjust RH Motion Control Handle Position Clean Engine and Exhaust System Area Caster Pivot Bearings Pre-Load AdjustmentRemove Engine Shrouds and Clean Cooling Fins Clean Debris From MachineBattery Disposal Clean Grass Build-Up Under DeckWaste Disposal Motor Oil DisposalProblem Possible Cause Corrective Action TroubleshootingTroubleshooting Troubleshooting Electrical Diagram SchematicsElectrical Schematic Hydraulic Diagram General Warranty Conditions and Products Covered Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 60 pages 42.39 Kb Manual 60 pages 43.2 Kb Manual 64 pages 37.72 Kb Manual 52 pages 8.82 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 60 pages 23.73 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 40 pages 46.04 Kb

920, 000 & higher specifications

The Exmark 920 is an exceptional piece of equipment tailored for professionals and enthusiasts alike. Designed with an emphasis on performance and reliability, this mower embodies the pinnacle of lawn care technology. Known for its robust construction, the Exmark 920 is equipped with a powerful engine, ensuring efficient and effective mowing even in demanding conditions.

One of the standout features of the Exmark 920 is its cutting deck. With a 52-inch or 60-inch mower deck option, it allows users to cover a large mowing area quickly. The deck is crafted from high-strength steel, providing durability and longevity while maintaining a lightweight design that enhances maneuverability. Innovative blade design promotes superior airflow for an even cut, preventing clumping and ensuring a polished finish across various grass types.

The Exmark 920 utilizes advanced technology, including the innovative RED Technology, which enhances engine performance by optimizing power consumption. This results in reduced fuel consumption while maintaining the required power output for demanding tasks. Additionally, the mower’s intuitive controls include a user-friendly interface, allowing for easy adjustments and settings, catering to the varying needs of different lawn types and conditions.

Another notable feature of the Exmark 920 is its all-day comfort design. With an ergonomic seat and advanced suspension system, operators can tackle long mowing sessions without discomfort. The padded seat is adjustable, providing maximum support to minimize fatigue, while the suspension system absorbs bumps and uneven terrain for a smoother ride.

Furthermore, the Exmark 920 prioritizes serviceability. Easy access points for maintenance and a well-designed layout ensure that routine tasks, such as oil changes and blade replacements, can be completed efficiently. The model also comes equipped with LED headlights for improved visibility during early morning or late evening mowing.

In summary, the Exmark 920 is a sophisticated mower combining power, advanced technology, and design for comfort and utility. Its high-performance engine, durable cutting deck, user-friendly controls, and serviceable layout make it an ideal choice for anyone seeking to achieve a well-manicured lawn with professional results. Whether for commercial or residential use, the Exmark 920 stands out as a leading option in the market, enabling users to tackle any mowing challenge with confidence and ease.
Top Page Image Contents