Exmark 000 & higher, 312 Using the Rollover Protection System Rops, Maintenance and Storage

Page 8

Safety

DANGER

Operating on wet grass or steep slopes can cause sliding and loss of control. Wheels dropping over edges, ditches, steep banks, or water can cause rollovers, which may result in serious injury, death or drowning.

Do Not mow slopes when grass is wet.

Do Not mow near drop-offs or near water.

Do Not mow slopes greater than 15 degrees.

Reduce speed and use extreme caution on slopes.

Avoid sudden turns or rapid speed changes.

Keep the roll bar in the raised and locked position and use seat belt.

See inside the back cover to determine the approximate slope angle of the area to be mowed.

Use a walk behind mower and/or a hand trimmer near drop-offs, ditches, steep banks or water. (Figure 3).

Figure 3

1.Safe Zone-Use the mower here on slopes less than 15 degrees

2.Danger Zone-Use a walk behind mower and/or hand trimmer on slopes greater than 15 degrees, near drop-offs and water.

3.Water

Remove or mark obstacles such as rocks, tree limbs, etc. from the mowing area. Tall grass can hide obstacles.

Watch for ditches, holes, rocks, dips and rises that change the operating angle, as rough terrain could overturn the machine.

Avoid sudden starts when mowing uphill because the mower may tip backwards.

Be aware that operating on wet grass, across steep slopes or downhill may cause the mower to lose traction. Loss of traction to the drive wheels may result in sliding and a loss of braking and steering.

Always avoid sudden starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly off the slope.

Follow the manufacturer’s recommendations for wheel weights or counter weights to improve stability.

Use extreme care with grass catchers or attachments. These can change the stability of the machine and cause loss of control.

Using the Rollover Protection System (ROPS)

A Rollover Protection System (roll bar) is installed on the unit.

WARNING

There is no rollover protection when the roll bar is down. Wheels dropping over edges, ditches, steep banks, or water can cause rollovers, which may result in serious injury, death or drowning.

Keep the roll bar in the raised and locked position and use seat belt.

Lower the roll bar only when absolutely necessary.

Do Not wear seat belt when the roll bar is down.

Drive slowly and carefully.

Raise the roll bar as soon as clearance permits.

Check carefully for overhead clearances (i.e. branches, doorways, and electrical wires) before driving under any objects and Do Not contact them.

In the event of a rollover, take the unit to an Authorized Service Dealer to have the ROPS inspected.

Maintenance and Storage

Disengage drives, lower implement, set parking brake, stop engine and remove key or disconnect spark plug wire. Wait for all movement to stop before adjusting, cleaning or repairing.

8

Image 8
Contents Lazer Z E-SERIES California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices TrainingSafety Operation Slope OperationUsing the Rollover Protection System Rops Maintenance and StorageSafety Safety Safety and Instructional Decals 109-7232 116-0157 116-3303 116-5944 117-2718 Message Display Systems SpecificationsModel Numbers Seat Hydrostatic Ground Drive SystemTires & Wheels Cutting DeckDimensions Accessory Weight Table Worksheet Torque RequirementsProduct Overview OperationControls Motion Control LeversIgnition Switch Choke ControlThrottle Control Brake LeverDrive Wheel Release Valves Fuel Shut-Off ValveFuel Gauge Pre-Start Operating InstructionsEngaging the PTO Open the Fuel Shut-Off ValveStarting the Engine Driving the Machine Disengaging the PTOStopping the Engine Driving Forward Adjusting the Cutting Height Adjusting the Deck Lift Foot Pedal 48 & 52 inch Decks OnlyTransporting a Unit Adjusting the Anti-Scalp RollersTransporting Loading a Unit Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelRecommended Jump Starting Procedure Do Not jump start a weak battery if these conditions existCheck Safety Interlock System Check Mower BladesService Air Cleaner Check Rollover Protections Systems Roll Bar KnobsCheck Seat Belt Check for Loose HardwareChange Engine Oil Check Hydraulic Oil LevelCheck Tire Pressures Check Condition Of BeltsLubricate Grease Fittings Lubricate Caster Wheel HubsLubricate Deck Lift Pivot Check Spark PlugsChange Fuel Filter Change Hydraulic System Filter and FluidWheel Hub Slotted Nut Torque Specification Check Spark Arrester if equippedThread Locking Adhesives Copper-Based Anti-seizeAdjustments Deck LevelingPump Drive Belt Tension Deck Belt TensionAdjusting the Parking Brake Electric Clutch AdjustmentRemoving the Shim Motion Control Linkage Adjustment Motion Control Damper Adjustment Motion Control Neutral Lock Pivot AdjustmentMotion Control Handle Adjustment Caster Pivot Bearings Pre-Load AdjustmentClean Hydro Cooling Fins Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Debris From Machine Clean Grass Build-Up Under DeckBattery Disposal Waste DisposalTroubleshooting Problem Possible Cause Corrective ActionSee Drive Wheel Release Valves section Troubleshooting Schematics PinkElectrical Logic Schematic-Kawasaki Schematics Electrical Logic Schematic-KohlerHydraulic Diagram Lazer Z E-Series Turf Equipment Page Page Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use Exmark Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 43.2 Kb Manual 64 pages 1.01 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 60 pages 23.73 Kb Manual 40 pages 46.04 Kb

0, 312, 000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.