Exmark 0, 312 manual Motion Control Handle Adjustment, Caster Pivot Bearings Pre-Load Adjustment

Page 44

Maintenance

Motion Control Handle Adjustment

Adjusting the height:

The motion control levers can be adjusted higher or lower for maximum operator comfort.

1.Remove the two bolts holding the control lever to the control arm shaft (Figure 38).

1.Loosen the screws on a cover plate (see Figure 39).

2.Slide the cover plate backward or forward to adjust the travel of the lever and tighten the screws.

3.Drive the machine and check the full forward tracking.

4.Repeat steps 1 through 3 until desired tracking is obtained.

 

 

Figure 38

 

 

 

Figure 39

 

 

 

 

 

RH Motion Control Shown

1.

Bolts

4.

Nuts

 

 

1.

Screw

3. Motion control lever

2.

Control lever

5.

Slotted holes

3.

Control arm shaft

 

 

2.

Cover plate

2.Move the control lever to the next set of holes. Secure the lever with the two bolts.

3.Repeat the adjustment for the opposite control lever.

Adjusting the Tilt

The motion control levers can be tilted fore or aft for maximum operator comfort.

1.Loosen the upper bolt holding the control lever to the control arm shaft.

2.Loosen the lower bolt just enough to pivot the control lever fore or aft Figure 38. Tighten both bolts to secure the control in the new position.

3.Repeat the adjustment for the opposite control lever.

Motion Control Full Forward Tracking Adjustment

If the machine travels or pulls to one side when the motion control levers are in the full forward position, adjust the cover plates.

Caster Pivot Bearings Pre-Load Adjustment

Remove dust cap from caster and tighten nyloc nut until washers are flat and back off 1/4 of a turn to properly set the pre-load on the bearings. If disassembled, make sure the spring disc washers are reinstalled as shown in Figure 40.

44

Image 44
Contents Lazer Z E-SERIES California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices TrainingSafety Operation Slope OperationUsing the Rollover Protection System Rops Maintenance and StorageSafety Safety Safety and Instructional Decals 109-7232 116-0157 116-3303 116-5944 117-2718 Message Display Systems SpecificationsModel Numbers Seat Hydrostatic Ground Drive SystemTires & Wheels Cutting DeckDimensions Accessory Weight Table Worksheet Torque RequirementsProduct Overview OperationControls Motion Control LeversIgnition Switch Choke ControlThrottle Control Brake LeverDrive Wheel Release Valves Fuel Shut-Off ValveFuel Gauge Pre-Start Operating InstructionsEngaging the PTO Open the Fuel Shut-Off ValveStarting the Engine Driving the Machine Disengaging the PTOStopping the Engine Driving Forward Adjusting the Cutting Height Adjusting the Deck Lift Foot Pedal 48 & 52 inch Decks OnlyTransporting a Unit Adjusting the Anti-Scalp RollersTransporting Loading a Unit Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelRecommended Jump Starting Procedure Do Not jump start a weak battery if these conditions existCheck Safety Interlock System Check Mower BladesService Air Cleaner Check Rollover Protections Systems Roll Bar KnobsCheck Seat Belt Check for Loose HardwareChange Engine Oil Check Hydraulic Oil LevelCheck Tire Pressures Check Condition Of BeltsLubricate Grease Fittings Lubricate Caster Wheel HubsLubricate Deck Lift Pivot Check Spark PlugsChange Fuel Filter Change Hydraulic System Filter and FluidWheel Hub Slotted Nut Torque Specification Check Spark Arrester if equippedThread Locking Adhesives Copper-Based Anti-seizeAdjustments Deck LevelingPump Drive Belt Tension Deck Belt TensionAdjusting the Parking Brake Electric Clutch AdjustmentRemoving the Shim Motion Control Linkage Adjustment Motion Control Damper Adjustment Motion Control Neutral Lock Pivot AdjustmentMotion Control Handle Adjustment Caster Pivot Bearings Pre-Load AdjustmentClean Hydro Cooling Fins Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Debris From Machine Clean Grass Build-Up Under DeckBattery Disposal Waste DisposalTroubleshooting Problem Possible Cause Corrective ActionSee Drive Wheel Release Valves section Troubleshooting Schematics PinkElectrical Logic Schematic-Kawasaki Schematics Electrical Logic Schematic-KohlerHydraulic Diagram Lazer Z E-Series Turf Equipment Page Page Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use Exmark Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 43.2 Kb Manual 64 pages 1.01 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 60 pages 23.73 Kb Manual 40 pages 46.04 Kb

0, 312, 000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.