Exmark 000 & higher, 312 manual See Drive Wheel Release Valves section

Page 48

Troubleshooting

Problem

 

Possible Cause

 

Corrective Action

 

 

 

 

 

Engine loses power

1.

Engine load is excessive

1.

Reduce the ground speed.

 

2.

Air cleaner is dirty.

2.

Clean or replace the air cleaner element.

 

3.

Oil level in the crankcase is low.

3.

Add oil to the crankcase.

 

4.

Cooling fins and air passages for the

4.

Remove the obstructions from the cooling

 

 

engine are plugged.

 

fins and air passages.

 

5.

Dirt in fuel filter.

5.

Replace the fuel filter.

 

6.

Dirt, water, or stale fuel is in the fuel

6.

Contact an Authorized Service Dealer.

 

 

system.

 

 

 

 

 

 

 

Mower pulls left or right (with levers fully

1.

Tire pressure in drive tires not correct.

1.

Adjust tire pressure in the drive tires.

forward)

 

 

 

 

 

 

 

 

 

Machine does not drive

1.

Drive release handle not in “operating”

1.

Position handle in “operating” position;

 

 

position.

 

see Drive Wheel Release Valves section

 

 

 

 

in Operation.

 

2.

Drive or pump belt is worn, loose or

2.

Change the belt.

 

 

broken.

 

 

 

3.

Drive or pump belt is off a pulley.

3.

Change the belt.

 

4.

Broken or missing idler spring.

4.

Replace the spring.

 

5.

Hydraulic fluid level is low or too hot.

5.

Add hydraulic fluid to reservoir or let it

 

 

 

 

cool down.

 

 

 

 

 

Uneven cutting height.

1.

Blade(s) not sharp.

1.

Sharpen the blade(s).

 

2.

Cutting blade(s) is/are bent.

2.

Install new cutting blade(s).

 

3.

Mower deck is not level.

3.

Level mower deck from side-to-side and

 

 

 

 

front-to-rear.

 

4.

Underside of mower is dirty.

4.

Clean the underside of the mower.

 

5.

Tire pressure in drive tires not correct.

5.

Adjust tire pressure in the drive tires.

 

6.

Blade spindle bent.

6.

Contact an Authorized Service Dealer.

 

7.

Tips of adjacent blades are at an uneven

7.

Replace blades, spindles and (or) check

 

 

cutting height. Blades tips should be even

 

for damage to mower deck.

 

 

within 3/16 inch which is approximately

 

 

 

 

one blade thickness.

 

 

 

 

 

 

 

Abnormal vibration

1.

Cutting blade(s) is/are bent or unbalanced.

1.

Install new cutting blade(s).

 

2.

Blade mounting bolt is loose.

2.

Tighten the blade mounting bolt.

 

3.

Engine mounting bolts are loose.

3.

Tighten the engine mounting bolts.

 

4.

Loose engine pulley, idler pulley, or blade

4.

Tighten the appropriate pulley.

 

 

pulley.

 

 

 

5.

Engine pulley is damaged.

5.

Contact an Authorized Service Dealer.

 

6.

Blade spindle is bent.

6.

Contact an Authorized Service Dealer.

 

 

 

 

 

Blades do not rotate.

1.

Deck belt is worn, loose or broken.

1.

Install new deck belt.

 

2.

Deck belt is off pulley.

2.

Install belt on clutch and deck pulleys,

 

 

 

 

idlers, and tensioning idler per routing

 

 

 

 

decal on deck.

 

3.

Broken or missing idler spring.

3.

Replace the spring.

 

4.

Drive belt not routed correctly.

4.

Refer to belt routing decal on deck.

 

 

 

 

 

48

Image 48
Contents Lazer Z E-SERIES California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices TrainingSafety Operation Slope OperationUsing the Rollover Protection System Rops Maintenance and StorageSafety Safety Safety and Instructional Decals 109-7232 116-0157 116-3303 116-5944 117-2718 Message Display Specifications Model NumbersSystems Seat Hydrostatic Ground Drive SystemTires & Wheels Cutting DeckDimensions Accessory Weight Table Worksheet Torque RequirementsProduct Overview OperationControls Motion Control LeversIgnition Switch Choke ControlThrottle Control Brake LeverFuel Shut-Off Valve Fuel GaugeDrive Wheel Release Valves Pre-Start Operating InstructionsOpen the Fuel Shut-Off Valve Starting the EngineEngaging the PTO Disengaging the PTO Stopping the EngineDriving the Machine Driving Forward Adjusting the Cutting Height Adjusting the Deck Lift Foot Pedal 48 & 52 inch Decks OnlyAdjusting the Anti-Scalp Rollers TransportingTransporting a Unit Loading a Unit Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelRecommended Jump Starting Procedure Do Not jump start a weak battery if these conditions existCheck Safety Interlock System Check Mower BladesService Air Cleaner Check Rollover Protections Systems Roll Bar KnobsCheck Seat Belt Check for Loose HardwareChange Engine Oil Check Hydraulic Oil LevelCheck Tire Pressures Check Condition Of BeltsLubricate Grease Fittings Lubricate Caster Wheel HubsLubricate Deck Lift Pivot Check Spark PlugsChange Fuel Filter Change Hydraulic System Filter and FluidWheel Hub Slotted Nut Torque Specification Check Spark Arrester if equippedThread Locking Adhesives Copper-Based Anti-seizeAdjustments Deck LevelingPump Drive Belt Tension Deck Belt TensionAdjusting the Parking Brake Electric Clutch AdjustmentRemoving the Shim Motion Control Linkage Adjustment Motion Control Damper Adjustment Motion Control Neutral Lock Pivot AdjustmentMotion Control Handle Adjustment Caster Pivot Bearings Pre-Load AdjustmentClean Engine and Exhaust System Area Remove Engine Shrouds and Clean Cooling FinsClean Hydro Cooling Fins Clean Debris From Machine Clean Grass Build-Up Under DeckBattery Disposal Waste DisposalTroubleshooting Problem Possible Cause Corrective ActionSee Drive Wheel Release Valves section Troubleshooting Schematics PinkElectrical Logic Schematic-Kawasaki Schematics Electrical Logic Schematic-KohlerHydraulic Diagram Lazer Z E-Series Turf Equipment Page Page Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use Exmark Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 43.2 Kb Manual 64 pages 1.01 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 60 pages 23.73 Kb Manual 40 pages 46.04 Kb

0, 312, 000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.