Exmark 312, 0 manual Motion Control Damper Adjustment, Motion Control Neutral Lock Pivot Adjustment

Page 43

Maintenance

Figure 35

1.Double nuts

8.Shut off unit. Remove jumper wire from wire harness and plug connector into seat switch.

9.Remove the jack stands.

10.Raise the deck and re-install the height of cut pin.

11.Check that the machine does not creep in neutral with the park brakes disengaged.

Motion Control Damper Adjustment

The top damper mounting bolt can be adjusted to obtain a more desired motion control lever resistance. See Figure 36 for mounting options.

Figure 36

RH Motion Control Shown

1.Torque nyloc nut to 200 in-lb (16.7 ft-lb). Bolt must protrude past end of nyloc nut after torque. A T-40 Torx bit will be necessary to hold the stud from turning.

2.Most resistance (firmest feel)

3.Damper

4.Medium resistance (medium feel)

5.Least resistance (softest feel)

Motion Control Neutral Lock Pivot Adjustment

The flanged nut can be adjusted to obtain a more desired motion control lever resistance (Figure 37).

Figure 37

1. Flanged nut

2. Jam nut

1.Loosen the jam nut.

2.Tighten or loosen the flanged nut to the desired feel.

For more resistance, tighten the flanged nut. For less resistance, loosen the flanged nut

3.Tighten jam nut.

43

Image 43
Contents Lazer Z E-SERIES California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Slope Operation OperationMaintenance and Storage Using the Rollover Protection System RopsSafety Safety Safety and Instructional Decals 109-7232 116-0157 116-3303 116-5944 117-2718 Message Display Model Numbers SpecificationsSystems Cutting Deck SeatHydrostatic Ground Drive System Tires & WheelsDimensions Torque Requirements Accessory Weight Table WorksheetMotion Control Levers Product OverviewOperation ControlsBrake Lever Ignition SwitchChoke Control Throttle ControlFuel Gauge Fuel Shut-Off ValveDrive Wheel Release Valves Operating Instructions Pre-StartStarting the Engine Open the Fuel Shut-Off ValveEngaging the PTO Stopping the Engine Disengaging the PTODriving the Machine Driving Forward Adjusting the Deck Lift Foot Pedal 48 & 52 inch Decks Only Adjusting the Cutting HeightTransporting Adjusting the Anti-Scalp RollersTransporting a Unit Loading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeDo Not jump start a weak battery if these conditions exist Recommended Jump Starting ProcedureCheck Mower Blades Check Safety Interlock SystemCheck for Loose Hardware Service Air CleanerCheck Rollover Protections Systems Roll Bar Knobs Check Seat BeltCheck Condition Of Belts Change Engine OilCheck Hydraulic Oil Level Check Tire PressuresLubricate Caster Wheel Hubs Lubricate Grease FittingsChange Hydraulic System Filter and Fluid Lubricate Deck Lift PivotCheck Spark Plugs Change Fuel FilterCopper-Based Anti-seize Wheel Hub Slotted Nut Torque SpecificationCheck Spark Arrester if equipped Thread Locking AdhesivesDeck Leveling AdjustmentsDeck Belt Tension Pump Drive Belt TensionElectric Clutch Adjustment Adjusting the Parking BrakeRemoving the Shim Motion Control Linkage Adjustment Motion Control Neutral Lock Pivot Adjustment Motion Control Damper AdjustmentCaster Pivot Bearings Pre-Load Adjustment Motion Control Handle AdjustmentRemove Engine Shrouds and Clean Cooling Fins Clean Engine and Exhaust System AreaClean Hydro Cooling Fins Waste Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Battery DisposalProblem Possible Cause Corrective Action TroubleshootingSee Drive Wheel Release Valves section Troubleshooting Pink SchematicsElectrical Logic Schematic-Kawasaki Electrical Logic Schematic-Kohler SchematicsHydraulic Diagram Lazer Z E-Series Turf Equipment Page Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use Exmark Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 43.2 Kb Manual 64 pages 1.01 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 60 pages 23.73 Kb Manual 40 pages 46.04 Kb

0, 312, 000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.