Exmark 000 & higher, 312 manual Troubleshooting, Problem Possible Cause Corrective Action

Page 47

Troubleshooting

Troubleshooting

Important: It is essential that all operator safety mechanisms be connected and in proper operating condition prior to mower use.

When a problem occurs, do not overlook the simple causes. For example: starting problems could be caused by an empty fuel tank.

The following table lists some of the common causes of trouble. Do not attempt to service or replace major items or any items that call for special timing of adjustment procedures (such as valves, governor, etc.). Have this work done by your Engine Service Dealer.

Note: When disconnecting electrical connectors DO NOT pull on the wires to separate the connectors.

Problem

 

Possible Cause

 

Corrective Action

 

 

 

 

 

Starter does not crank

1.

PTO is engaged.

1.

Disengage the PTO.

 

2.

Parking brake is not engaged.

2.

Set the parking brake.

 

3.

Drive levers are not in neutral lock

3.

Ensure the drive levers are in the neutral

 

 

position.

 

lock position.

 

4.

Battery does not have a full charge.

4.

Charge the battery. See Check

 

 

 

 

Battery Charge and Recommended

 

 

 

 

Jump Starting Procedure sections in

 

 

 

 

Maintenance.

 

5.

Electrical connections are corroded, loose

5.

Check the electrical connections for

 

 

or faulty.

 

good contact. Clean connector terminals

 

 

 

 

thoroughly with electrical contact cleaner,

 

 

 

 

apply dielectric grease and reconnect.

 

6.

Fuse is blown.

6.

Replace the blown fuse.

 

7.

Relay or switch is defective.

7.

Contact an Authorized Service Dealer.

 

8.

Faulty module.

8.

Replace module.

 

 

 

 

 

Engine will not start, starts hard, or fails to

1.

Fuel tank is empty.

1.

Fill the fuel tank.

keep running

2.

Fuel shutoff valve is closed.

2.

Open the fuel shutoff valve.

 

 

3.

Oil level in the crankcase is low.

3.

Add oil to the crankcase.

 

4.

The throttle and choke are not in the

4.

Be sure the throttle control is midway

 

 

correct position.

 

between the “SLOW” and “FAST”

 

 

 

 

positions, and the choke is in the “ON”

 

 

 

 

position for a cold engine or the “OFF”

 

 

 

 

position for a warm engine.

 

5.

Dirt in fuel filter.

5.

Replace the fuel filter.

 

6.

Dirt, water, or stale fuel is in the fuel

6.

Contact an Authorized Service Dealer.

 

 

system.

 

 

 

7.

Air cleaner is dirty.

7.

Clean or replace the air cleaner element.

 

8.

Seat switch is not functioning properly.

8.

Check the seat switch indicator. Replace

 

 

 

 

seat if needed.

 

9.

Electrical connections are corroded, loose

9.

Check the electrical connections for

 

 

or faulty.

 

good contact. Clean connector terminals

 

 

 

 

thoroughly with electrical contact cleaner,

 

 

 

 

apply dielectric grease and reconnect.

 

10.

Relay or switch is defective.

10.

Contact an Authorized Service Dealer.

 

11.

Faulty spark plug.

11.

Clean, adjust or replace spark plug.

 

12.

Spark plug wire is not connected.

12.

Check the spark plug wire connection.

 

13.

Faulty module.

13.

Replace module.

 

 

 

 

 

47

Image 47
Contents Lazer Z E-SERIES California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Slope Operation OperationMaintenance and Storage Using the Rollover Protection System RopsSafety Safety Safety and Instructional Decals 109-7232 116-0157 116-3303 116-5944 117-2718 Message Display Systems SpecificationsModel Numbers Cutting Deck SeatHydrostatic Ground Drive System Tires & WheelsDimensions Torque Requirements Accessory Weight Table WorksheetMotion Control Levers Product OverviewOperation ControlsBrake Lever Ignition SwitchChoke Control Throttle ControlDrive Wheel Release Valves Fuel Shut-Off ValveFuel Gauge Operating Instructions Pre-StartEngaging the PTO Open the Fuel Shut-Off ValveStarting the Engine Driving the Machine Disengaging the PTOStopping the Engine Driving Forward Adjusting the Deck Lift Foot Pedal 48 & 52 inch Decks Only Adjusting the Cutting HeightTransporting a Unit Adjusting the Anti-Scalp RollersTransporting Loading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeDo Not jump start a weak battery if these conditions exist Recommended Jump Starting ProcedureCheck Mower Blades Check Safety Interlock SystemCheck for Loose Hardware Service Air CleanerCheck Rollover Protections Systems Roll Bar Knobs Check Seat BeltCheck Condition Of Belts Change Engine OilCheck Hydraulic Oil Level Check Tire PressuresLubricate Caster Wheel Hubs Lubricate Grease FittingsChange Hydraulic System Filter and Fluid Lubricate Deck Lift PivotCheck Spark Plugs Change Fuel FilterCopper-Based Anti-seize Wheel Hub Slotted Nut Torque SpecificationCheck Spark Arrester if equipped Thread Locking AdhesivesDeck Leveling AdjustmentsDeck Belt Tension Pump Drive Belt TensionElectric Clutch Adjustment Adjusting the Parking BrakeRemoving the Shim Motion Control Linkage Adjustment Motion Control Neutral Lock Pivot Adjustment Motion Control Damper AdjustmentCaster Pivot Bearings Pre-Load Adjustment Motion Control Handle AdjustmentClean Hydro Cooling Fins Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Waste Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Battery DisposalProblem Possible Cause Corrective Action TroubleshootingSee Drive Wheel Release Valves section Troubleshooting Pink SchematicsElectrical Logic Schematic-Kawasaki Electrical Logic Schematic-Kohler SchematicsHydraulic Diagram Lazer Z E-Series Turf Equipment Page Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use Exmark Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 43.2 Kb Manual 64 pages 1.01 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 60 pages 23.73 Kb Manual 40 pages 46.04 Kb

0, 312, 000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.