Unigreen LASER-FUTURA- EXPO series AT STD/TOP - AT BASE manual Preliminary Checks

Page 9

4.2PRELIMINARY CHECKS

When you receive the machine, check that it is complete and no parts are missing.

If there are any damaged parts, inform your local reseller or UNIGREEN directly in good time.

When the machine is delivered, make sure you ask:

a)that the machine is delivered with all of its parts fitted and that the fitting meets the requisites in table N° 14b-15b-16b (pages 37, 38, 39).

This procedure is necessary because for reasons of space during transportation the machine is often delivered partially dismantled.

b)that it is tested in your presence in particular checking:

=that the suction filter and the inside of the tank are clean and free of work residues.

=that the connections are made correctly following the basic layout (FIG. N° 17, page 16).

=that the hose clips and all the unions and connections are tightened properly.

=that all of the protective covers are fitted solidly to the machine, in particular the protective cover of the power-takeoff of the pump.

=that the multiplier is sufficiently supplied with lubricant oil.

=that the zone where the fan turns hasn’t been bent by knocks during transportation.

4.3TRANSPORTING AND MOVING THE MACHINE

Every time you have to lift the machine, before starting the operation, always make sure the lifting gear and the relevant tools and equipment (cables, hooks, etc..) are suitable for lifting the load and check the stability of the same.

It is forbidden to unhook and move the machine with the tank full.

The dry weight of the machine at the maximum level of fitting and with all the accessories allowed is stamped on the nameplate; use slings and lifting gear with a adequate load-bearing capacity (FIG.3).

Never lift or move the mistblowers by hand if there is liquid in the tank. The machine will weigh more and the movement of the liquid can change the centre of gravity causing uncontrolled movements.

We recommend using slings as shown in the figure, the lifting points to use on the machine are indicated with the relevant symbol.

Don’t lift the machine with the forks of a forklift truck because the machine can tip over due to the overhanging weight of the blower group.

Don’t pass or stand under the machine when it is being lifted.

4.3.1TOWED ATOMISERS PARKING

Don’t stand the mistblower on unstable ground or steep slopes, the machine is designed to be parked safely on compact ground with a slope of up to 8.5° using the relevant chocks (FIG. 4) in the following way:

- Machine parked with drawbar uphill (max 8.5°), place the chocks behind the wheels.

- Machine parked with drawbar downhill (max 8.5°), place the chocks in front of the wheels.

- Machine parked across the slope (max 8.5°), place one chock in front of the drawbar wheel (in the direction of the slope) and the other in front of the wheel uphill.

MOVING

To lift the machine, follow the instructions above.

The towed mistblowers have an extendable drawbar parking wheel so the machine can be moved around by hand on flat, compact ground, with the tank empty.

To make moving the mistblower around easier when it is disconnected from the tractor, on the machine and on the drawbar there are supports for positioning the:

-cardan shaft: hinged rest on the drawbar parking wheel.

-manual pressure regulator: bayonet housing on the drawbar.

-electric pressure regulator: pushbutton panel support (the cable must be coiled around the same to stop it getting in the way).

-Brake levers if fitted: bayonet housing on the drawbar.

FIG.3

Only move and lift the machine with the tank empty

FIG.4

This symbol identifies the coupling points of the machine

unigreen 9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents 09/2006 USE and Maintenance ManualSummary Hand Lances Maintenance Guarantee Composition of the ManualProduct Responsibility Unigreen spa is not responsible if Key to the symbols Intended USE Using Chemical ProductsProhibited USE RecommendationsWeather Conditions Characteristics and SpecificationsDriving on the Road Tables of Fittings AllowedStandards of Reference Noise Level of the MachineUSER’S Instructions Description of the Machine Hand Washing TanksPreliminary Checks Transporting and Moving the MachineTowed Atomisers Parking Tractor Coupling Adjustable HubsDrawbar with Towing EYE or Fork Steering Drawbar Coupledto ElevatorCardan Shaft PumpSuction Filter Components of the Pressure Regulator Pressure RegulatorControl box for GCP Elettrico electrical regulators General InstructionsDelivery Filters only Equipped Models Filling the Tank Test with Clean WaterManual Premixing MixingPremixer on Cover Optional MAXCircuit Washer Andtank Washer Washing the AtomiserAxial Blower Group with Pulley Blower GroupAxial Blower Group with Multiplier Blower Group with Front SuctionClutch Axial RotorCannon Blower Group Manually Inclinabile HeadOIL Feed from Tractor for hydraulic systems Normal Volume Conical Nozzles Over 500L/HASpraying Description of Type of Jets Description of Type of NozzlesANTI-DRIFT Nozzles LOW Volume Conical Nozzles 150-500L/HACalibrating Axial FAN Atomisers Speed 6 Km. / hTreatments on Tall Plants Calibrating Cannon Atomisers Tables on pagesTreatments on Herbaceous Cultivations Hand LancesProgrammed Maintenance MaintenanceRoutine Maintenance Cleaning the NozzlesStorage in a Warehouse and Transportation Putting Back Into Service After Winter LayupDemolition and Disposal Materials for DemolitionCommonly used spare parts TR80-01 Arancio Tables for Calibrating Mistblowers Ø600-650 Calibrating TableTables for Calibrating Mistblowers Ø700-750 Tables for Calibrating Mistblowers Ø800 Tables for Calibrating Mistblowers Ø900 Tables for Calibrating Mistblowers Ø800 TGZ Tables for Calibrating Mistblowers Ø650 TGZTables for Calibrating Cannons Ø450 Calibrating Table for Cannons23 m Tables for Calibrating Cannons Ø400 440108 121 136 Pressure Tables of Delivery of Nozzles for AtomisersPressure BAR JET Tables of Delivery of Nozzles for Hand LancesTable of Programmed Maintenance Operation PROBLEMS, Causes and Solutions50 h 300 h TAB.14B Allowed Fittings Group TAB.15B Allowed FittingsTAB.16B Allowed Fittings Member of the group

LASER-FUTURA- EXPO series AT STD/TOP - AT BASE specifications

The Unigreen LASER-FUTURA-EXPO series, specifically the models AT STD/TOP and AT BASE, represents a groundbreaking advancement in the realm of agricultural technology. Designed for precision and efficiency, these laser-guided systems are engineered to meet the demands of modern farming practices. The LASER-FUTURA-EXPO series is synonymous with innovation and high performance, offering a range of features and technologies that enhance productivity.

One of the standout characteristics of the AT STD/TOP model is its advanced laser guidance system. This technology allows for unparalleled accuracy in land leveling and grading, ensuring that the soil is prepared perfectly for planting. The integration of top-grade lasers significantly reduces human error and increases operational efficiency. For farmers, this means that crops can be established in an optimized environment, leading to healthier yields.

The AT BASE variant provides a cost-effective solution while still delivering essential laser-fueled functionalities. This model maintains the fundamental technologies of the series but offers a streamlined approach to achieving precision farming. Both models feature durable construction designed to withstand the rigors of outdoor use while providing operators with a user-friendly experience.

A notable technology incorporated into the LASER-FUTURA-EXPO series is its real-time monitoring capabilities. This allows farmers to track their operations seamlessly, making adjustments on-the-fly based on the live data collected. This feature significantly enhances decision-making processes, enabling proactive management of equipment and resources.

The ergonomic design of both the AT STD/TOP and AT BASE models facilitates ease of use, with intuitive controls that allow operators to focus on their tasks without unnecessary distraction. Additionally, maintenance is simplified, ensuring that downtime is minimized and productivity maximized.

In summary, the Unigreen LASER-FUTURA-EXPO series AT STD/TOP and AT BASE models epitomize modern agricultural innovation. With advanced laser guidance, real-time monitoring, and user-friendly design, these systems empower farmers to optimize their operations while promoting sustainable practices. As agriculture continues to evolve, products like the LA-SER-FUTURA-EXPO are at the forefront, enabling a new era of efficiency and productivity in farming.
Top Page Image Contents