Utica PEG-C Thermostat Installation, Lighting Instructions, For Your Safety Read Before Operating

Page 13

THERMOSTAT INSTALLATION

1.Thermostat should be installed on an inside wall at least two feet from an uninsulated or outside wall, approximately four feet above the floor.

2.NEVER install a thermostat on an outside wall.

3.Do not install a thermostat where it will be affected by:

A.Drafts

B.Hot or cold pipes

C.Sun light

D.Lighting fixtures

E.Television

F.Fireplace or chimneys

4.Check thermostat operation by raising and lowering thermostat as required to start and stop the burners.

5.Instructions for the final adjustment of the thermostat are packaged with the thermostat ( adjusting heating anticipator, calibration, etc.).

LIGHTING INSTRUCTIONS

WARNING:

IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EX-

ACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

Before any procedures are attempted on this appliance, it is necessary to determine if the ignition system is intermittent or continuous pilot system. If you are uncertain, contact the manufacturer before proceeding.

CAUTION:

Before operating, make certain steam boiler is full of water

to water line and system is vented of air. See the operating lighting instructions.

LIGHTING PROCEDURE FOR BOILER WITH

INTERMITTENT PILOT SYSTEM.

FOR YOUR SAFETY READ BEFORE OPERATING.

A.This appliance is equipped with an ignition system which automatically lights the pilot. Do not try to light the pilot by hand.

B.Before operating smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

CAUTION: WHAT TO DO IF YOU SMELL GAS:

*Do not try to light any appliance.

*Do not touch any electrical switch.

*Do not use any phone in your building.

*Immediately call your gas supplier from a neighbor's phone.

*Follow your gas supplier's instructions.

*If you cannot reach your gas supplier, call the fire department.

PAGE 11

Page 12 Page 14
Image 13
Page 12 Page 14
Contents PEG-C Table of Contents Read ALL Instructions Before Installing Safety SymbolsInstallation Procedure Ventilation & Combustion AIR Page Connecting Supply and Return Piping Page Vent Installation Vent System Modification Installation Vent Damper Installation InstructionsInstructions Electrical Wiring Connecting GAS ServiceSee Addendum a for Wiring Diagrams and Component Coding For Your Safety Read Before Operating Thermostat InstallationLighting Instructions Operating Instructions for Intermittent Pilot Systems To Turn OFF GAS to Appliance Lighting Instructions for Continuous Pilot SystemNormal Sequence of Operation Connecting Supply Return PIPING, Water Chilled Medium Discharge will be Boiling HOT Water and Steam General InstructionsWill be Boiling HOT Water Water will be Boiling HOT To Clean the Boiler FluewaysSkimming OFF Impurities Water will be Boiling HOT Using Cleaning CompoundBlowing Down Boiler Page 24VOLT Spark PEG-C Replacement Parts PilotManifold PEG300C PEG-C Replacement Parts BaseSide Panel Right ALL PEG-C Replacement Parts JacketsWash 5/16 Flat STL ZP PEG-C Replacement Parts Heat ExchangerPEG-C Replacement Parts Front Panel Controls PEG-C Replacement Parts Electrical Natural GAS Steam Boilers RATINGS, DATA, and Dimensions

PEG-C specifications

Utica PEG-C, a modern combination of both technology and innovation, has emerged as a solution tailored for those seeking efficient heating solutions in residential and commercial spaces. Standing out in the market, this high-performance boiler is designed not only to optimize heating efficiency but also to enhance user comfort and convenience.

At the core of the Utica PEG-C is its advanced cast iron construction, which ensures durability and longevity. The cast iron heat exchangers play a crucial role in maximizing heat transfer while minimizing energy losses. This design is pivotal in meeting energy efficiency standards, making it an eco-friendly choice in today’s environmentally conscious world.

One of the standout features of the Utica PEG-C is its automated combustion control system. This state-of-the-art technology allows for precise regulation of the burner operation, ensuring that fuel usage is minimized without compromising on heat output. Consequently, users can expect reduced utility bills with increased comfort levels in their living or working environments.

The PEG-C series also offers a range of input capabilities, making it suitable for various applications, from small homes to larger commercial buildings. The flexibility in sizing ensures that customers can select a unit that efficiently matches their heating requirements. Moreover, the integrated smart controls further enhance operational efficiency by adjusting the heating output based on real-time temperature readings.

Safety is paramount in any heating system, and Utica PEG-C does not fall short in this regard. It features an array of safety mechanisms, including an automatic water fill, pressure relief valves, and flame rollout switches. These features guarantee safe operation, providing peace of mind to users.

Additionally, the PEG-C series offers compatibility with a range of heating options, including hydronic baseboard systems, radiant floors, and indirect water heaters, making it a versatile choice for many heating applications.

In summary, the Utica PEG-C combines robust engineering, cutting-edge technology, and a commitment to efficiency and safety. With its durable construction, intelligent control systems, and adaptability to various heating needs, it's a wise investment for anyone looking to enhance their heating systems whether in a residential or commercial context.
Top Page Image Contents