Seagate ST36530N/W/WC, ST39140N/W/WC/LW/LC manual Additional jumper options for W/LW drives

Page 52

50

Medalist Pro Installation Guide, Rev. B

W/LW drives

Other applicable jumper options

Other option jumpers are available as illustrated below.

Drive with

 

 

 

 

 

 

 

 

 

HDA up, PCB

 

 

 

 

 

 

 

 

 

down, viewed

 

 

 

 

 

Pin 1

from front

HDA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

J6

 

L

R

 

 

 

 

 

 

 

Reserved E

E A

3

A

2

A

1

A

0

 

D

S

 

 

 

Reserved

 

 

 

 

 

 

 

 

 

Remote

11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LED

12

 

 

 

 

 

 

 

CATH

 

 

 

 

 

 

 

 

Shipped with cover installed.

 

 

 

 

 

 

Do not remove.

 

 

 

 

 

 

 

 

Do not install jumpers

 

 

 

 

 

 

 

on these four positions.

 

 

 

 

 

 

 

Drive Front

 

J6

 

 

 

J6

 

 

 

 

Jumper Type

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(enlarged to

 

 

 

 

 

 

 

 

 

show detail)

 

 

 

 

 

 

 

 

Pin 1

 

 

 

 

 

 

 

 

 

End

 

 

 

 

 

J2

 

 

 

 

 

 

 

 

 

 

 

 

Pin 1

DC Power

 

 

 

 

 

 

 

 

 

Connector

 

 

 

 

 

 

 

 

 

 

 

J1

 

 

 

 

 

 

SCSI I/O

 

J2 Jumper Type

Connector

 

 

 

(enlarged to

show detail)

 

 

J2

Pin 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Reserved

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Delay Motor Start option

 

 

 

 

(valid only if the Enable

 

 

 

 

Motor Start jumper is

 

 

 

 

not connected)

 

 

 

 

Disable the Delay Motor

 

 

 

(default)

Start option.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Motor start delay equal

 

 

 

 

 

 

 

 

 

 

 

to the SCSI ID multiplied

 

 

 

 

by 12 seconds. For

 

 

 

 

 

 

example, if the SCSI

 

 

 

 

 

 

ID = 2, the drive starts

 

 

 

 

in 24 seconds.

 

 

 

 

 

 

 

Motor Start option

 

 

 

 

 

Disable motor start

 

 

(default). The drive

 

(default)

starts according to the

 

 

 

 

 

 

 

 

 

 

 

 

Delay Motor Start option.

 

 

 

 

 

Enable motor start. The

 

 

 

 

 

 

 

 

 

 

 

drive waits for the Start

 

 

Unit command from the

 

 

 

 

host before starting the

 

 

 

 

 

 

 

spindle motor.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Write Protect option

 

 

 

 

 

 

Write protect = Off

 

 

 

 

 

(default)

(enables writing.

 

 

 

 

 

Write protect = On

 

 

 

 

 

 

 

 

 

(disables writing).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Parity Check option

 

 

 

 

 

 

 

 

 

Enable parity check of

 

 

 

 

 

 

 

 

(default)

SCSI bus.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Disable parity check.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 15. Additional jumper options for W/LW drives

Image 52
Contents ST39140N/W/WC/LW/LC Contents Handling precautions PrefaceElectrostatic discharge protection Important safety information and precautions Medalist Pro Installation Guide, Rev. B Wichtige Sicherheitshinweise Medalist Pro Installation Guide, Rev. B Page Electromagnetic susceptibility Regulatory agency complianceElectromagnetic compliance Electromagnetic compliance for the European Union Australian C-TickSeagate Technology support services Presales Support Customer Service CSO European Support Services Africa/Middle East Support Services SeaFAX General description Drive characteristics RPMDCX DC power requirements Amps for LW/LC Models ST39140 ST34520Medalist Pro Installation Guide, Rev. B Dimensions of the drive General information Drive modelsScsi ID jumpers Drive termination Terminator power Circuits and data path widthsInterconnect characteristics for single-ended I/O circuits Interconnect characteristics for LVD I/O circuits Fifty pin I/O connection to drive Multiple drive connection to host adapter Multiple-drive connection to host adapter Medalist Pro Installation Guide, Rev. B Providing adequate cooling Kühlung des Systems Suggested air flow Abbildung 4. Empfohlener Luftstromverlauf Mounting the drive and connecting cables Installation des Laufwerkes und Anschluß der KabelMedalist Pro Installation Guide, Rev. B DC power connector Abbildung 5. Gleichstromanschluß Hinweis Page Mounting configuration dimensions Formatting the drive Quick reference desktop system notesSetting the Scsi ID jumpers Setting the Scsi ID on model N drivesTerminating the drive Terminating the driveSetting terminator power jumpers Other applicable jumper options Additional jumper optionsLW drives Host Alternate Enable Scsi terminator Disable Scsi terminator Model only Terminator power Additional jumper options for W/LW drives Additional jumper option for LW drives WC/LC drives Applicable jumper options Jumper optionsLC drives Additional jumper options for LC drives Page