Windsor ADM8, 10080170 Vacuum Motor Replacement, Maintenance, WARNING The green

Page 20
VACUUM MOTOR REPLACEMENT
Wire Terminal

MAINTENANCE

!WARNING:

ONLY QUALIFIED MAINTENANCE PERSONNEL ARE TO PERFORM THE FOLLOWING REPAIRS.

VACUUM MOTOR REPLACEMENT

1.Turn off all switches and unplug machine.

2.Remove recovery tank.

3.Remove the (2) screws that fasten the solution tank to the frame, and tilt tank back to expose the inside of the frame.

4.Locate the vacuum motor wires and disconnect at the connector. Close the solution tank.

5.Remove the (6) screws holding the vacuum motor cover (p/n 27809) to the solution tank.

6.Remove the vacuum motor.

7.Reverse process to install vacuum motor.

Vacuum Motor Carbon Brushes Replacement (Windsor)

 

End Cap

Carbon

WARNING: The green

Brushes

ground wire must be

 

attached for safe operation.

 

See wiring diagram.

If armature commutator is grooved, extremely pitted or not concentric, the motor will need to be replaced or sent to a qualified service center.

Important:

These brushes wear quicker as the length shortens due to increased heat. Spring inside brush housing will damage motor if brushes are allowed to wear away completely.

Vacuum Motor Carbon Brushes Replacement (Windsor) 38 [9.5mm]

Periodically check the length of the carbon brushes. Replace both carbon brushes when either is less than 3/8" (9.5mm) long.

Vacuum Motor Carbon Brushes Replacement (Ametek)

 

End Cap

Carbon

WARNING: The green

Brushes

ground wire must be

 

attached for safe operation.

 

See wiring diagram.

Note: When replacing carbon brushes loosen wire terminal BEFORE removing screws on bracket.

Wire

Terminal

Note:

Place stop in groove.

If armature commutator is grooved, extremely pitted or not concentric, the motor will need to be replaced or sent to a qualified service center.

Important:

These brushes wear quicker as the length shortens due to increased heat. Spring inside brush housing will damage motor if brushes are allowed to wear away completely.

WARNING: The green 3/8 (9.5mm)

Periodically check the length of the carbon brushes. Replace both carbon brushes when either is less than 3/8" (9.5mm) long.

4-3

ADMIRAL 86038230 03/16/07

Image 20
Contents Operating Instructions MODEL ADM810080170CARPET EXTRACTOR 86038320 03/16/07 PRV NOMODEL MACHINE DATA LOG/OVERVIEWYOUR DEALER TABLE OF CONTENTS HOW TO USE THIS MANUALSAFETY MAINTENANCEHOW TO USE THIS MANUAL SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING THIS MACHINEThis machine is for commercial use IMPORTANT SAFETY INSTRUCTIONSHAZARD INTENSITY LEVEL HAZARD INTENSITY LEVELFOR SAFETY WHEN SERVICING MACHINEGROUNDING INSTRUCTIONS GROUNDING INSTRUCTIONSELECTRICAL TECHNICAL SPECIFICATIONS POWER TYPEGENERAL DIMENSIONS/WEIGHT BRUSH SPEED 1000 rpm10.Recovery Dump Hose. Facilitates draining 11.Solution Dump Hose. Facilitates drainingCONTROLS/COMPONENT LOCATIONS 3.Electrical Cord11 1 9 2 6.Recovery Tank Dome 7.Vacuum ShoeCONTROLS/COMPONENT LOCATIONS 1.Solution Intake Cover 2.Vacuum Intake Cover 3.Float Shut-Off 4.Clean-OutOpening 5.Pour SpoutCONTROLS/COMPONENT LOCATIONS 6.Lift HandleFILLING OPERATIONS CHEMICALSOPERATIONS CORRECT INCORRECTAdjust handle to comfortable operating OPERATIONSCLEANING PROCEDURE CLEANING PROCEDURE STEP3-10 ACCESSORY TOOL USAGEAPRV NO SERVICE SCHEDULE MAINTENANCEDAILY / REGULAR MAINTENANCE MAINTENANCEPERIODIC MAINTENANCE VACUUM MOTOR REPLACEMENT MAINTENANCEVacuum Motor Carbon Brushes Replacement Windsor Vacuum Motor Carbon Brushes Replacement AmetekMAINTENANCE BELT REPLACEMENT86249420 PRV NO. 86287330 PRV NO MAINTENANCE SOLUTION PUMP REPLACEMENTWIRING DIAGRAM 8626829086268460 86268430TROUBLESHOOTING CHART PROBLEMSOLUTION CAUSEADMIRAL 86038230 03/16/07 SEE PG FRAME ASSEMBLYSEE PG FRAME ASSEMBLY 27 19 2030 BRUSH ASSEMBLY16 12 BRUSH ASSEMBLY PUMP ASSEMBLY SEE PGPUMP ASSEMBLY VACUUM SHOE ASSEMBLY ADMIRAL 86038230 03/16/07VACUUM SHOE ASSEMBLY CONTROL PANEL ASSEMBLY SEE PG5-10 CONTROL PANEL ASSEMBLYSOLUTION TANK ASSEMBLY 12 12A 10 12BSEE PG 20 15 7 11 14*195-12 SOLUTION TANK ASSEMBLYADMIRAL 86038230 03/16/07 RECOVERY TANK ASSEMBLY5-13 5-14 RECOVERY TANK ASSEMBLYSUGGESTED SPARE PARTS 5-15