Windsor 10052300, SCEOX264 Squeegee Blades, Adjusting Squeegee, To Remove Squeegee Assembly

Page 24

MAINTENANCE

2. SQUEEGEE BLADES

The front squeegee blade allows solution to pass through channels in the blade into the squeegee assembly while maintaining vacuum to provide lift. The front blade has four wear surfaces and can be rotated for extended life. The front blade should not require regular replacement under normal use.

The rear blade wipes the floor to a near dry condition. It is important the rear blade be in good condition to properly do its job. As with the front, each squeegee blade assembly has four wear surfaces for extended service.

Check both the front and rear squeegee blades for damage, wear, and adjustment each day in the pre- run check. Change the front blade if it is torn or has an uneven edge. Change the rear blade if it is less than 1/2 the original thickness.

ADJUSTING SQUEEGEE

Adjusting the squeegee is a two-part process. First, the squeegee assembly must have correct pitch in order for the squeegee blade to have the same deflection at each tip as well as the center. The knob on the squeegee linkage controls the pitch adjustment. The second adjustment is the deflection. Knobs on each end of the squeegee control this.

SQUEEGEE DEFLECTION

CORRECT

NOT ENOUGH

TOO MUCH

SQUEEGEE SIDE VIEW OF

TO REMOVE SQUEEGEE ASSEMBLY

1.With the squeegee in the up position, turn key switch “OFF”.

2.Disconnect vacuum hose from squeegee and loosen both knobs.

3.Pull squeegee assembly rearward from the lifting carrier.

4.Inspect or repair as necessary and reinstall.

TO REPLACE OR ROTATE REAR SQUEEGEE BLADES

1.With the squeegee in the up position, turn key switch “OFF”.

FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key.

2.Remove the squeegee assembly from the machine. Unlatch and remove blade retainer strap and remove squeegee blade.

3.Rotate the squeegee to new edge position or replace as required. Each blade has four new edge positions.

4.Install blade on locating pins of squeegee assembly.

5.Install squeegee retainer strap.

6.Fasten and lock latch, adjust latch only tight enough to take up slack in retaining strap.

TO REPLACE OR ROTATE FRONT SQUEEGEE BLADE

1.With the squeegee in the up position, turn key switch “OFF”.

2.Remove the squeegee from the machine. Loosen three thumbscrews and remove the retainer strap and squeegee blade.

3.Rotate the squeegee to new edge position or replace as required. Each blade has four new edge positions. When installing the front blade, tighten the center thumbscrew first. Insure that the retainer strap is pressed against the blade before tightening the outer screws.

4-6

CUTTER 24V (SCE) 86037020 04/04/07

 

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Walk Behind Scrubber Machine Data LOG/OVERVIEW Your DealerOverview Table of Contents HOW to USE this Manual ModelImportant Safety Instructions Read ALL Instructions Before Using this MachineHazard Intensity Level Hazard Intensity LevelSafety Label Location Technical Specifications DIMENSION/CAPACITYSpecial Notes MeasureHOW the Machine Works Components Controls KEY Switch Emergency SHUT-OFF SwitchBrush Switch Solution Control Knob Vacuum SwitchSqueegee Pitch Adjustment Knob Squeegee Deflection Adjustment KnobsBrush Pressure Indicator Parking BrakeHour Meter Emergency Stop Procedures Filling Solution TankMachine Operation PRE-RUN Machine InspectionNormal Scrubbing To Begin ScrubbingTo Stop Scrubbing Recovery Tank Emptying and Cleaning TanksDouble Scrub Service Schedule MaintenanceMaintenance Daily WeeklyMaintenance Battery Maintenance BatteriesChecking Battery Specific Gravity Battery ConditionTo Charge the Batteries Checking GravityChanging Batteries Adjusting Squeegee To Remove Squeegee AssemblySqueegee Blades To Replace or Rotate Rear Squeegee BladesTo Adjust Squeegee Pitch To Adjust Amount of Rear Squeegee DeflectionTo Replace AQUA-MIZER Squeegee Blades Replacing or Installing Scrub Brushes Recovery Tank Float SHUT-OFFScrub Brushes Uncoated FloorsSolution Strainer Brush Motor Carbon Brush ReplacementBrush Motor Changing Brush MotorsTraction Motor Carbon Brush Replacement Traction MotorCircuit Breakers Brush Shrouds & Brush SkirtsVacuum Motor Changing Vacuum MotorActuator Scrub Deck REMOVAL/REPLACEMENT Scrub Deck Actuator AdjustmentRecommended Greasing Machine Troubleshooting Problem Cause SolutionMachine Troubleshooting

86037020, SCEX324, 10052290, SCEOX324, SCEX264 specifications

The Windsor SCEOX264, SCEX324, SCEX264, 86037020, and 10052320 are advanced technology solutions that cater to modern computational and networking needs. Each model showcases a unique combination of features designed to optimize performance, efficiency, and user experience.

The SCEOX264 stands out with its focus on high-definition video processing. Equipped with an exceptional decoding capability, it handles multiple formats while maintaining superior image quality. The integrated algorithms enhance video rendering, reducing latency and minimizing buffer times. This makes it ideal for applications in broadcasting and video conferencing, where seamless visual communication is essential.

The SCEX324, on the other hand, is designed for robust data storage and management. It supports a wide array of storage configurations, ensuring high data availability and security. Featuring cutting-edge encryption technologies, SCEX324 guarantees that sensitive information remains protected against unauthorized access. Its rapid access times and scalability make it suitable for enterprises needing agile data solutions.

The SCEX264 is renowned for its comprehensive connectivity capabilities. With support for multiple network protocols, it seamlessly integrates into diverse environments. The unit's ability to handle large data streams allows for smooth connectivity even during peak usage times, making it perfect for organizations embracing digital transformation.

Models 86037020 and 10052320 further enhance the lineup with their specialized functionalities. 86037020 focuses on energy efficiency, using advanced power management technologies to reduce operational costs without sacrificing performance. Its environmentally friendly design aligns with sustainability goals pursued by many modern organizations.

In contrast, 10052320 emphasizes user interface and experience. It features an intuitive design that simplifies interactions, reducing the learning curve for users. Its compatibility with various operating systems ensures versatility across different platforms, making it an ideal choice for diverse corporate ecosystems.

Collectively, these models reflect a commitment to innovation and quality, making them viable options for businesses looking to upgrade their technological infrastructure. They not only address the growing demand for high performance and security but also pave the way for future advancements in computing and data management. With a focus on user-centric design and advanced functionalities, these models are tailored for success in an increasingly digital world.
Top Page Image Contents