Windsor SCEOX264, SCEX264, SCEX324, 86037020, 10052330 Solution Strainer, Changing Brush Motors

Page 27

6.SOLUTION STRAINER

The solution strainer is located in front of the left front wheel. The solution strainer protects the solenoid valve from debris. If there is little or no solution flow to the ground, check the strainer for debris. Drain the solution tank and clean the solution strainer. To remove the strainer, turn the bottom part of the strainer counterclockwise until the bottom is separated. Clean out the debris from the wire mesh and re-assemble. Make sure the O-ring gasket is in place when re-assembled

7.BRUSH MOTOR

!

Do not use a pressure washer to clean around the brush motors. Use tap pressure only.

CHANGING BRUSH MOTORS

1.With the scrub deck in the stored position, disconnect brush motor wiring connector from harness.

2.Remove shrouds from scrub deck to access and remove scrub brushes or pad drivers.

3.Remove retaining bolt, lock washer, flat washer and star drive from brush motor shaft.

4.Remove 4 brush motor mounting bolts located under scrub deck.

5.Remove brush motor.

6.Reverse steps to install.

MAINTENANCE

BRUSH MOTOR CARBON BRUSH

REPLACEMENT

1.Scribe alignment mark on motor barrel to motor cap. Remove two bolts.

2.Remove end cap from motor.

NOTE: Motors contain two wave washers in cap. Do not lose these.

3.Release brush from spring tension. Remove screw connecting brush wire lead to brush holder. Clean brush holder to insure free movement.

4.Retract spring and install new brush. Install connector screw and lead.

5.When all new brushes are installed. Place all in retracted position, held into brush holder by spring tension.

6.Carefully place end cap onto bearing on motor shaft.

NOTE: Use care to assure wave washer alignment.

7.With end cap in partially installed position, release all brushes to contact position with motor commutator.

NOTE: Failure to insure all brushes are released will result in motor failure.

8.Reset end cap and realign with scribe marks on motor barrel. Reinstall the two attach bolts from cap into base.

9.Maintain alignment between motor barrel base and cap.

CUTTER 24V (SCE) 86037020 04/04/07

4-9

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Walk Behind Scrubber Machine Data LOG/OVERVIEW Your DealerOverview Table of Contents Model HOW to USE this ManualRead ALL Instructions Before Using this Machine Important Safety InstructionsHazard Intensity Level Hazard Intensity LevelSafety Label Location DIMENSION/CAPACITY Technical SpecificationsMeasure Special NotesHOW the Machine Works Components Controls KEY Switch Emergency SHUT-OFF SwitchBrush Switch Squeegee Deflection Adjustment Knobs Solution Control KnobVacuum Switch Squeegee Pitch Adjustment KnobBrush Pressure Indicator Parking BrakeHour Meter PRE-RUN Machine Inspection Emergency Stop ProceduresFilling Solution Tank Machine OperationNormal Scrubbing To Begin ScrubbingTo Stop Scrubbing Recovery Tank Emptying and Cleaning TanksDouble Scrub Weekly Service ScheduleMaintenance Maintenance DailyMaintenance Batteries Battery MaintenanceChecking Gravity Checking Battery Specific GravityBattery Condition To Charge the BatteriesChanging Batteries To Replace or Rotate Rear Squeegee Blades Adjusting SqueegeeTo Remove Squeegee Assembly Squeegee BladesTo Adjust Squeegee Pitch To Adjust Amount of Rear Squeegee DeflectionTo Replace AQUA-MIZER Squeegee Blades Uncoated Floors Replacing or Installing Scrub BrushesRecovery Tank Float SHUT-OFF Scrub BrushesChanging Brush Motors Solution StrainerBrush Motor Carbon Brush Replacement Brush MotorBrush Shrouds & Brush Skirts Traction Motor Carbon Brush ReplacementTraction Motor Circuit BreakersChanging Vacuum Motor Vacuum MotorScrub Deck Actuator Adjustment Actuator Scrub Deck REMOVAL/REPLACEMENTRecommended Greasing Problem Cause Solution Machine TroubleshootingMachine Troubleshooting

86037020, SCEX324, 10052290, SCEOX324, SCEX264 specifications

The Windsor SCEOX264, SCEX324, SCEX264, 86037020, and 10052320 are advanced technology solutions that cater to modern computational and networking needs. Each model showcases a unique combination of features designed to optimize performance, efficiency, and user experience.

The SCEOX264 stands out with its focus on high-definition video processing. Equipped with an exceptional decoding capability, it handles multiple formats while maintaining superior image quality. The integrated algorithms enhance video rendering, reducing latency and minimizing buffer times. This makes it ideal for applications in broadcasting and video conferencing, where seamless visual communication is essential.

The SCEX324, on the other hand, is designed for robust data storage and management. It supports a wide array of storage configurations, ensuring high data availability and security. Featuring cutting-edge encryption technologies, SCEX324 guarantees that sensitive information remains protected against unauthorized access. Its rapid access times and scalability make it suitable for enterprises needing agile data solutions.

The SCEX264 is renowned for its comprehensive connectivity capabilities. With support for multiple network protocols, it seamlessly integrates into diverse environments. The unit's ability to handle large data streams allows for smooth connectivity even during peak usage times, making it perfect for organizations embracing digital transformation.

Models 86037020 and 10052320 further enhance the lineup with their specialized functionalities. 86037020 focuses on energy efficiency, using advanced power management technologies to reduce operational costs without sacrificing performance. Its environmentally friendly design aligns with sustainability goals pursued by many modern organizations.

In contrast, 10052320 emphasizes user interface and experience. It features an intuitive design that simplifies interactions, reducing the learning curve for users. Its compatibility with various operating systems ensures versatility across different platforms, making it an ideal choice for diverse corporate ecosystems.

Collectively, these models reflect a commitment to innovation and quality, making them viable options for businesses looking to upgrade their technological infrastructure. They not only address the growing demand for high performance and security but also pave the way for future advancements in computing and data management. With a focus on user-centric design and advanced functionalities, these models are tailored for success in an increasingly digital world.
Top Page Image Contents