Windsor SCEOX324, SCEOX264 To Adjust Squeegee Pitch, To Adjust Amount of Rear Squeegee Deflection

Page 25

TO ADJUST SQUEEGEE PITCH

1.Choose a smooth, level surface. Turn “ON” the key switch. Lower the squeegee and drive forward at least 2 feet (60cm.).

2.With the squeegee down, stop the machine. Do not allow machine to roll back.

FOR SAFETY: Before leaving or servicing the machine; stop on level surface, turn off machine and remove key.

3.Determine the differences, if any, in deflection of the squeegee blade between each end and the middle. Proper adjustment is obtained when deflection is equal all the way across the squeegee blade. The bubble level should also indicate when the squeegee is adjusted properly. When the air bubble is in the center of the vial, the deflection should be even across the squeegee blade.

4.To decrease the deflection of the squeegee blade at the ends, tighten knob near the squeegee center. To increase the deflection at the ends of the squeegee assembly, loosen knob.

5.Check the deflection of the squeegee blades again. Repeat steps 1 through 4 until the deflection is equal across the entire rear squeegee blade.

3/8”

PROPER DEFLECTION OF SQUEEGEE BLADE

MAINTENANCE

TO ADJUST AMOUNT OF REAR SQUEEGEE DEFLECTION

1.Choose a smooth, level surface. Lower the squeegee and drive forward at least 2 feet (60cm).

2.With the squeegee down, stop the machine. Do not allow machine to roll back.

FOR SAFETY: Before leaving or servicing machine; stop on level surface, turn off machine and remove key.

3.Observe the amount of squeegee deflection. It should deflect 3/8 in. (9.5mm) across the entire width of the squeegee.

4.To increase the squeegee deflection, turn the 2 knobs at the squeegee ends counter-clockwise. To decrease the deflection, turn the knobs clockwise.

NOTE: The deflection should be consistent along the length of the squeegee. If the deflection varies from end to end the knobs can be adjusted independently to correct the variation.

5.Turn on the key switch. Raise, then lower squeegee assembly. Drive forward at least 2 feet (60cm).

6.Repeat steps 2 through 4 until deflection of 3/8 in. (9.5mm) is reached.

3.TO REPLACE AQUA-MIZER

SQUEEGEE BLADES

These squeegee blades have two wear edges. To use the second edge:

1.Remove deck shrouds.

2.Remove brushes or pad drivers.

3.Remove each of the Aqua-Mizer squeegee systems.

4.Remove the hardware from each system that retains the blade.

5.Flip the blades and replace hardware.

6.Re-install each Aqua-Mizer system, brushes or pad drivers and shrouds.

CUTTER 24V (SCE) 86037020 04/04/07

4-7

 

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Walk Behind Scrubber Your Dealer Machine Data LOG/OVERVIEWOverview Table of Contents Model HOW to USE this ManualRead ALL Instructions Before Using this Machine Important Safety InstructionsHazard Intensity Level Hazard Intensity LevelSafety Label Location DIMENSION/CAPACITY Technical SpecificationsMeasure Special NotesHOW the Machine Works Components Controls Emergency SHUT-OFF Switch KEY SwitchBrush Switch Vacuum Switch Solution Control KnobSqueegee Pitch Adjustment Knob Squeegee Deflection Adjustment KnobsParking Brake Brush Pressure IndicatorHour Meter Filling Solution Tank Emergency Stop ProceduresMachine Operation PRE-RUN Machine InspectionTo Begin Scrubbing Normal ScrubbingTo Stop Scrubbing Emptying and Cleaning Tanks Recovery TankDouble Scrub Maintenance Service ScheduleMaintenance Daily WeeklyMaintenance Batteries Battery MaintenanceBattery Condition Checking Battery Specific GravityTo Charge the Batteries Checking GravityChanging Batteries To Remove Squeegee Assembly Adjusting SqueegeeSqueegee Blades To Replace or Rotate Rear Squeegee BladesTo Adjust Amount of Rear Squeegee Deflection To Adjust Squeegee PitchTo Replace AQUA-MIZER Squeegee Blades Recovery Tank Float SHUT-OFF Replacing or Installing Scrub BrushesScrub Brushes Uncoated FloorsBrush Motor Carbon Brush Replacement Solution StrainerBrush Motor Changing Brush MotorsTraction Motor Traction Motor Carbon Brush ReplacementCircuit Breakers Brush Shrouds & Brush SkirtsChanging Vacuum Motor Vacuum MotorScrub Deck Actuator Adjustment Actuator Scrub Deck REMOVAL/REPLACEMENTRecommended Greasing Problem Cause Solution Machine TroubleshootingMachine Troubleshooting

86037020, SCEX324, 10052290, SCEOX324, SCEX264 specifications

The Windsor SCEOX264, SCEX324, SCEX264, 86037020, and 10052320 are advanced technology solutions that cater to modern computational and networking needs. Each model showcases a unique combination of features designed to optimize performance, efficiency, and user experience.

The SCEOX264 stands out with its focus on high-definition video processing. Equipped with an exceptional decoding capability, it handles multiple formats while maintaining superior image quality. The integrated algorithms enhance video rendering, reducing latency and minimizing buffer times. This makes it ideal for applications in broadcasting and video conferencing, where seamless visual communication is essential.

The SCEX324, on the other hand, is designed for robust data storage and management. It supports a wide array of storage configurations, ensuring high data availability and security. Featuring cutting-edge encryption technologies, SCEX324 guarantees that sensitive information remains protected against unauthorized access. Its rapid access times and scalability make it suitable for enterprises needing agile data solutions.

The SCEX264 is renowned for its comprehensive connectivity capabilities. With support for multiple network protocols, it seamlessly integrates into diverse environments. The unit's ability to handle large data streams allows for smooth connectivity even during peak usage times, making it perfect for organizations embracing digital transformation.

Models 86037020 and 10052320 further enhance the lineup with their specialized functionalities. 86037020 focuses on energy efficiency, using advanced power management technologies to reduce operational costs without sacrificing performance. Its environmentally friendly design aligns with sustainability goals pursued by many modern organizations.

In contrast, 10052320 emphasizes user interface and experience. It features an intuitive design that simplifies interactions, reducing the learning curve for users. Its compatibility with various operating systems ensures versatility across different platforms, making it an ideal choice for diverse corporate ecosystems.

Collectively, these models reflect a commitment to innovation and quality, making them viable options for businesses looking to upgrade their technological infrastructure. They not only address the growing demand for high performance and security but also pave the way for future advancements in computing and data management. With a focus on user-centric design and advanced functionalities, these models are tailored for success in an increasingly digital world.
Top Page Image Contents