Watson & Sons 520DUN user manual How to get out of auto operation

Page 72

￿The pump is automatically switched into auto-restart mode and displays the ! icon. The only keys active are STOP, AUTO/MAN, DIRECTION and START (available only as an extended keypress to toggle keypad lock). UP and DOWN keys are available if manual scaling has been set (see below).

￿If the remote direction input is active and the direction-enable link is applied, the DIRECTION key is disabled. If keypad lock is set, only STOP and START (available as an extended keypress to toggle keypad lock) are active.

￿The pump displays whichever of four auto running screens is appropriate according to the previously selected auto mode - 4-20mA or 0-10V with or without scaling in place.

￿The auto running screens display four pieces of information: the speed at which the pump rotates after receiving a low signal on Analogue 1 (4mA or 0V); the speed at which the pump rotates after receiving a high signal on Analogue 1 (20mA or 10V); the set speed (that is: the speed at which the pump is current- ly rotating according to the analogue speed signal and the analogue scaling sig- nal if scaling is set); and the flowrate in the units selected (see 18.8 Flow units). The scaling percentage is also displayed if it is set.

￿If manual scaling is enabled using the Setup menu (see 18 Setup), the scaling percentage can be adjusted between 0% and 100% using the UP and DOWN keys.

￿The pump responds to remote digital inputs. If the run / stop input stops the pump, the bottom line of the auto running screen shows “Remote stop”. When it starts the pump again, this will disappear and the pump returns to normal running mode.

￿If the pump is stopped because a leak is detected, the screen displays “LEAK DETECTED. Check and reset, then press Stop”. See 25.1 Error codes.

￿The remote status outputs operate fully.

How to get out of auto operation

￿Pressing the AUTO/MAN key displays three options: Analogue, Manual and Network. Use the UP and DOWN keys to choose and press ENTER to con- firm.

￿Selecting Manual returns the pump to manual operation. Using this method of changing from AUTO/MAN, the pump retains the set speed from its pre- vious operation in manual mode in a stopped condition. See 14 Manual operation.

￿Selecting Network puts the pump into network (RS485) mode. See 24 Network control and operation.

￿Selecting Analogue returns the pump to analogue mode. It responds to the analogue signal as soon as this is done and shows the “AUTO” icon.

￿Alternatively, make the remote auto / manual input go low (0V). The pump returns to manual operation and retains the set speed and run status from its previous operation in analogue mode.

Watson-Marlow 520DuN IP66/NEMA 4X User Manual

72

Page 71 Page 73
Image 72
Page 71 Page 73
Contents Contents Watson-Marlow 520DuN IP66/NEMA 4X pumpsPublication history 104 Decontamination certificate 105 Declaration of conformity Declaration of incorporationFive year warranty Cased pumps, 620 cased pumps and 720 cased pumpsConditions ExceptionsWhen you unpack your pump Packaging disposalInspection Components supplied 520DuN pump, IP66 Nema 4X modelsInformation for returning pumps StoragePeristaltic pumps an overview How they workSuitable applications Safety notes Page Pump specifications Remote control 520DuN, IP66 Nema 4X modelManual control Analogue controlIP Ingress Protection and Nema definitions NemaPump specifications Standards HarmonisedStandards OtherDimensions 520DuN IP66/NEMA 4X model Unit weightsGood pump installation practice General recommendationsDo’s and do not’s Page Connecting this product to a power supply Page Page Switching the pump on for the first time Start-up check listFirst-time start-up defaults Language Analogue inputSpeed User trimPump is now ready to operate Keypad functions in manual mode Manual operationPage Page Keypad lock Keypad beepManual operation and remote digital inputs and outputs Main menu Keypad functions in menu screensMain menu entry PIN-secure process protection Calibrate Head and tube TubeCalibration dose Page Setup Setup menuTrim Analogue Input 1 speed Program Trim Scaling strokeDisplay AlternativelyPump number BaudStop bits 18.7 Xon/XoffFlow units Run time General alarm OutputsParameters are Run / stopPage Remote stop Page Auto-restart Set maximum speed Backlight18.15 ROM LanguageDefaults BeepSecurity code Pin out details ExitMemoDose To dispense a master doseChanging dosing speed To repeat the doseExit Automatic control wiring 22.1 520N module removal and replacementTo remove the 520N watertight module To replace the 520N watertight module Wiring up Page Do not strap the control and mains power cables together Speed analogue input Scaling analogue input Speed analogue output Tachometer frequency outputSwitch Run / stop inputDirection input Tube monitor 520N module Wire colour Auto / manual toggle inputMemoDose input Leak detection inputOutputs 1, 2, 3 Supply voltagesImportant pump status outputs 22.14 RS485 input DC Voltage Max load Typical useHow to get into auto operation Automatic control and operationHow to get out of auto operation Emergency stop How to get into network operation Network control and operationHow to get out of network operation 24.1 RS485 command strings Command Parameters MeaningTroubleshooting Error codes Error condition Suggested actionDrive maintenance Drive spares520R, 520R2 and 520RE pumpheads Identification of parts520REL/520REM/520REH Pumphead position, removal and replacement To reposition the trackRotor replacement Rotor removal29 520R, 520R2 and 520RE installation Opening the pumphead guard29.2 520R and 520R2 tube loading 29.3 520RE fitting the drain port 29.4 520RE Element loading 520REL Pressures Up to 2 bar 30 psiPressures Up to 4 bar 60 psi Up to 7 bar 100 psi 2mm and 6.4mm Industrial SanitaryPage Sanitary 3⁄4in mini-Tri-clamp connectors Industrial quick-release connectors29.5 520RE Element connection 30 520R, 520R2 and 520RE maintenance 31 520R, 520R2 and 520RE rotor settings General guide to cleaning with solventsChemical Cleaning precautions Pumphead spares 520R/520R2 520REL/520REM/520REHFlow rates Pumping conditions520R and 520R2 520RE Continuous tubing 220rpmElements Performance curves Page Page Page Tubing and element part numbers 6mm wall tubing for 520R pumpheads4mm wall tubing for 520R2 pumpheads Inch Marprene Bioprene Pumpsil913.A008.024 Inch Chem-Sure Sta-Pure4mm wall elements for 520RE pumpheads Sanitary Inch Bioprene TM Sta-Pure102 35 520 series pumping accessories Accessory Description Part code Pump Compatibility103 Trademarks Publication history104 Decontamination certificate RGA number Signature Your position Date105

520DUN specifications

Watson & Sons 520DUN is a state-of-the-art model that has garnered attention for its exceptional performance and innovative technologies. Designed for agricultural applications, this machine combines durability, efficiency, and ease of use, catering to the needs of modern farmers.

One of the standout features of the 520DUN is its robust engine. Equipped with a high-performance diesel engine, it offers impressive horsepower, allowing it to handle a variety of demanding tasks with ease. This engine is designed for fuel efficiency, ensuring that operators can complete their work without frequent refueling. The powertrain is complemented by an advanced transmission system that enables smooth gear shifts, enhancing operator comfort during long hours of operation.

The 520DUN also boasts a remarkable load capacity, making it an ideal choice for transporting heavy materials. Its rugged build quality ensures that it can withstand the rigors of daily use, providing a reliable solution for farmers and contractors alike. The robust chassis and reinforced components were designed to maintain stability and control, especially when navigating uneven terrain.

Incorporating cutting-edge technologies, the Watson & Sons 520DUN features precision farming capabilities. With GPS integration, operators can efficiently manage their fields, optimizing planting and harvesting processes. This technology not only increases yield but also minimizes inputs, making farming more sustainable and economically viable.

User ergonomics were a significant consideration in the design of the 520DUN. The operator's cabin is spacious and well-equipped with intuitive controls, providing a comfortable working environment. Operators will appreciate the advanced display panel that offers real-time data on performance metrics, fuel consumption, and maintenance reminders. This allows users to keep the machine in peak condition and react to any issues promptly.

Safety is also paramount in the design of the 520DUN. It features reinforced safety measures, including roll-over protection systems and visibility enhancements, ensuring operator safety during operations.

In summary, the Watson & Sons 520DUN represents the pinnacle of agricultural machinery with its powerful engine, remarkable load capacity, precision technology, and ergonomic design. It is tailored for those who seek reliability and efficiency in their agricultural endeavors, making it a noteworthy choice in today's competitive market.
Top Page Image Contents