Wayne-Dalton WDTC-20 user manual WaveProgramming Operation, Press and Release Bind button

Page 26

Z-Wave®Programming

26

Z-Wave®Programming

and Operation

Z-Wave®controllers from various manufacturers may support the Z-Wave®Thermostat General V2 Device Class used by the Wayne-Dalton Z-Wave®Enabled Thermostat. The following procedure will allow the thermostat to be added to a Z-Wave®network with its full functionality.

NOTE: For Wayne-Dalton controller models, HA-07WD and HA-09WD, please proceed to the next page, “Alternate method of Z-Wave®Programming and Operation.”

GENERAL PROGRAMMING DIRECTIONS (For controllers with full thermostat device class compatability) :

1.Set your primary controller to INCLUDE mode, to add the thermostat as a node on your network (see your specific controller’s User Manual for detailed instructions.)

2.Press and release the BIND button on the thermostat.

Your controller will indicate the thermostat was successfully added to its network (see your specific controller’s User Manual for details.) Also, your thermostat will indicate it was successfully added to the network by flashing the entire Z-Wave®logo.

For other controller specific tasks such as adding the thermostat to Scenes or Groups, or deleting the thermostat as a node, use the BIND button to activate the Z-Wave®signal.

OPERATION:

See your specific controller’s User Manual for detailed instructions on operating your thermostat. If your controller supports full thermostat device class functions then the following remote features are available:

a)Up and Down Temperature Control.

b)Change between HEAT and COOL modes.

c)Change between NORMAL and SAVE ENERGY modes.

d)Read the current temperature.

e)Read target temperatures for NORMAL and SAVE ENERGY modes.

f)Set target temperatures for NORMAL and SAVE ENERGY modes.

g)Set indicator to Red, Green, Amber or Off.

TIP: Prior to Z-Wave®Programming, be certain the thermostat does not belong to another Z-Wave®network by observing the Z-Wave®logo on the display. If the complete logo with waves flashing is present, use your controller to remove the thermostat from the network. See your specific controller’s User Manual for details on removing devices (nodes) from a Z-Wave®network.

 

 

Press and Release

BIND button

2

 

 

 

 

COOL

 

 

RESET

 

 

NORMAL SAVE

 

 

ENERGY

COOL

Full Z-Wave®logo

NOTE: An example of programming to a controller with full functionality is shown on page 28.

Continued Next Page

Page 25 Page 27
Image 26
Page 25 Page 27
Contents This manual should be retained for future reference For Model WDTC-20Important Notice Manual Operation Programming Target Temperatures 23-25 Table of ContentsTable of Contents WaveProgrammingBasics GlossaryWaveEnabled Thermostat Basics Tools required Package ContentsGeneral Information Installation NextWall Pencil to prevent Wires from fallingRemoving Existing Thermostat Into wall openingMounting Base Screws Pull the wires through the wire hole in the baseThermostat Control Unit Mounting Base Matches your wiring needs. a needle-nose Opening. Do not allow wiring betweenConnect labeled wires only to a terminal Thermostat mounting base and wallOW2 W Y RH RC G a Wiring InformationHeat Pump Systems Jumper Reference Guide ResetIMPORTANT! Additional Wiring Notes JP5 JP3 JP4 JP1 JP2Wire W2 W RH Y Wire Heat/Cool + CWire RH Y WireCommon Designations for Zoned Hot Water Systems Cross Reference ChartModify Label Scheme Common Designations for Lennox Heat Pump SystemsRH RC G a Wire Heat + C Wiring and Jumper ConfigurationJP5 RH GTerminals on the thermostat base. Wrap wire around Wire Heat/Cool + C Wiring and Jumper ConfigurationStep B Connect your wires to the corresponding JP5 JP3 JP4 JP1JP5 JP3 JP4 JP1 JP2 Or O Y RH GO W2 W Y RH RC G a JP2W2 W Y Your Labeled Wires Box to the leftSecurely using a Phillips or slotted screwdriver W2 W Slotted screwdriverLow Battery Icon Located on Thermostat LCD Display + AACheck Heat Return to Auto position for Normal operationCelsius/Fahrenheit Readout Advanced Installation InformationTemperature Offset JP1General Operation Reference Guide OperationGeneral Operation Basics   Programming Target temperatures ProgrammingButton. Target Temp will appear in the display Programming Save Heat target temperatureProgramming Normal Cool target temperature ProgrammingHeat mode, if the temperature falls more than Programming Cool Save target temperaturePress and Release Bind button WaveProgrammingWaveProgramming Operation Full Z-WavelogoAlternate Programming Directions Press the ADD Device button in the ThinkEssentials window Programming ExamplesWaveProgramming ThinkEssentials Example Design TAB Operating ThermostatNormal to Save Energy Programming ExamplesOn the Wireless Gateway, press WaveProgramming Example with WDHA-12RRemoving Thermostat from Wireless Gateway primary controller WaveAlternate Programming Example with HA-09WD Press and release the Bind button onWaveAlternate Programming ControllerCustomer Support

WDTC-20 specifications

The Wayne-Dalton WDTC-20 is an innovative and versatile garage door opener that stands out in terms of performance, security, and user-friendliness. Designed by Wayne-Dalton, a leader in the garage door industry, the WDTC-20 incorporates modern technologies to provide homeowners with a complete solution for their garage access needs.

One of the main features of the WDTC-20 is its powerful motor which delivers reliable lifting force suitable for standard and heavier doors. The unit is engineered to ensure smooth and quiet operation, making it ideal for residential use where noise reduction is a priority. The opener is compatible with various door types, allowing for easy integration with sectional or one-piece garage doors.

The WDTC-20 incorporates advanced security technology with its rolling code feature. This system generates a new code every time the remote is used, significantly reducing the risk of unauthorized access. Additionally, the opener includes a secure manual release system, providing peace of mind in case of power outages.

A hallmark of the WDTC-20 is its user-friendly interface. The opener features a bright LED lighting system that illuminates the garage space, enhancing visibility during entry and exit. The unit also boasts a wireless keypad option that allows users to open the garage door without needing to carry a remote. This is particularly convenient for households with multiple users.

For tech-savvy homeowners, the WDTC-20 offers smartphone compatibility through its smart hub. By connecting to a home Wi-Fi network, users can control and monitor the garage door remotely via a mobile app. This feature allows notifications for door status, facilitating enhanced security and operability.

In terms of installation, the WDTC-20 is designed for easy and straightforward setup, enabling users to quickly benefit from its extensive features. Additionally, Wayne-Dalton offers robust customer support and a warranty program for peace of mind.

Overall, the Wayne-Dalton WDTC-20 combines strength, security, and technological innovation, making it a compelling choice for anyone in need of a modern garage door opener. Its blend of convenience and safety features ensures that it caters well to the dynamic needs of contemporary living.
Top Page Image Contents